Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Ceramic Glass
Cleaning off the cooktop before and after each use will help keep
it free from stains and provide the most even heating. For more
information, see "General Cleaning" section.
I
Do not store jars or cans above the cooktop. Dropping a
heavy or hard object onto the cooktop could crack the
cooktop.
I
Do not leave a hot lid on the cooktop. As the cooktop cools,
air can become trapped between the lid and the cooktop,
and the ceramic glass could break when the lid is removed.
I
For food containing sugar in any form, clean up all spills and
soils as soon as possible. Allow the cooktop to cool down
slightly. Remove the spills while the surface is still warm. You
may want to wear oven mitts while cleaning the cooktop. If
sugary spills are allowed to cool down, they can adhere to the
cooktop and can cause pitting and permanent marks.
I
Do not slide cookware or bakeware across the cooktop.
Aluminum or copper bottoms and rough finishes on
cookware or bakeware could leave scratches or marks on the
cooktop.
I
Do not allow objects that could melt, such as plastic or
aluminum foil, to touch any part of the entire cooktop.
I
Do not use the cooktop as a cutting board.
I
Use cookware about the same size as the surface cooking
area. Cookware should not extend more than ½" (1.3 cm)
outside the area.
A. Surface cooking area
B. Cookware/canner
C. ½" (1.3 cm) Maximum overhang
I
Use flat-bottomed cookware for best heat conduction and
energy efficiency. Cookware with rounded, warped, ribbed or
dented bottoms will cause uneven heating and poor cooking
results.
I
Determine flatness by placing the straight edge of a ruler
across the bottom of the cookware. While you rotate the ruler,
no space or light should be visible between it and the
cookware.
I
Make sure the bottoms of pots and pans are clean and dry
before using them. Residue and water can leave deposits
when heated.
B
A
C
Home Canning
IMPORTANT: Aluminum canners or canners that are not
completely flat on the bottom will not activate the cooking
surface area. See "Cookware" section.
When canning for long periods, alternate the use of surface
cooking areas between batches. This allows time for the most
recently used areas to cool.
I
Center the canner on the largest surface cooking area.
Canners should not extend more than ½" (1.3 cm) beyond
the surface cooking area.
I
Do not place canner on 2 surface cooking areas at the same
time.
I
For more information, contact your local agricultural
department. Companies that manufacture home canning
products can also offer assistance.
Cookware
Only ferromagnetic pans can be used for induction cooking.
Ferromagnetic materials include:
I
Enameled steel
I
Cast iron
I
Stainless steel designed for induction cooking
Non-ferromagnetic materials include:
These types of pans will not work with induction cooking.
I
Stainless steel
I
Glass
I
Ceramic
I
Copper or aluminum pans
To find out whether your pans can be used with an induction
cooktop, flip the pan over, hold a magnet to the bottom of the
pan, and see whether it sticks.
The number on the surface cooking area heat setting display will
flash if no pan is placed on the surface cooking area, or the pan is
not made of the right material, or it is not the right size. It will stop
flashing once a suitable pan is placed on the surface cooking
area. If you take longer than 90 seconds to place the correct pan
on the surface cooking area, the surface cooking area will turn
off.
Ideal cookware should have a flat bottom, straight sides and a
well-fitting lid, and the material should be of medium-to-heavy
thickness.
Choose the correct pan size for each surface cooking area. The
diameter of the pan's base should correspond to the size of the
surface cooking area.
NOTE: Cookware manufacturers often give the diameter across
the top of the pan. This is usually larger than the diameter of the
base.
Pans with rough finishes may scratch the cooktop.
7
Publicité
Table des Matières
Dépannage
