Honeywell FocusPRO TH6320WF Informations Sur Le Produit

Programmable
Thermostat
Product
Information
Home screen quick reference
Once your Wi-Fi thermostat is installed, it will display the home screen.
Portions of this display will change depending on how you are viewing it.
Set up messages
describe steps in
the Wi-Fi set up
process
Set clock, day,
Select fan
or schedule
settings
The screen lights when you press any button. It stays lit for 8 seconds
after you complete changes.
Connecting to your Wi-Fi network
1 Connect to your thermostat.
1a Make sure the thermostat displays Wi-Fi SETUP.
1b On the wireless device (tablet, laptop,
smartphone), view the list of available Wi-Fi networks.
1c Connect to the network called NewThermostat_123456 (the
number will vary).
Note: If you are asked to specify a home, public, or office network,
select Home Network.
2 Join your home network.
2a Open your web browser to access the Thermostat Wi-Fi Setup page.
The browser should automatically direct you to the correct page; if
it does not, go to http://192.168.1.1
2b Find the name of your home network on this page and select it.
Note: Some routers have enhanced features such as guest networks; use
your home network.
2c Complete the instructions for joining your Wi-Fi network and click on
the Connect button. (Depending on your network setup, you may see
an instruction such as Enter Password for your home network.)
Note: If you did not correctly connect to the thermostat, you may see your
home router page. If so, return to Step 1.
Note: If your Wi-Fi network does not appear in the list on the Thermostat
Wi-Fi Setup page:
• Try performing a network rescan by pressing the Rescan button.
This is helpful in areas with a lot of networks.
• If you are connecting to a hidden network, then enter the network
SSID in the textbox, select the encryption type from the drop down
menu, and click on the Add button. This manually adds the network
to the top of the list. Click on the new network in the list and enter
the password if necessary. Click on Connect to join the network.
3 Make sure your thermostat is connected.
While the connection is in process, your thermostat will flash Wait for
up to 3 minutes. When the connection is complete, the display will
show Wi-Fi Setup Connection Success. The Wi-Fi signal strength will appear
in the top-right corner.
After about 60 seconds, the home screen will appear and Register at
Total Connect will flash until registration is complete.
Note: If the thermostat displays Connection Failure or continues to display
Wi-Fi Setup, confirm you correctly entered your home network password in
step 2.
Wi-Fi status
Temperature
adjustment
buttons
HOLD
Permanent
override
button
M31586
Additional
Select system
settings
mode
FocusPRO® TH6320WF
Wi-Fi® Series
Registering your thermostat online
To view and set your Wi-Fi thermostat remotely, you must have a Total
Connect Comfort account. Follow the instructions below.
1 Open the Total Connect Comfort web site.
Go to www.mytotalconnectcomfort.com
Setting the time and day
1 Press Set Clock/Day/Schedule, then press
2 Press Set Day, then press
s
3 Press Done to save.
Note: If the Set Clock/Day/Schedule option is not displayed, press Done.
Note: If the display flashes Set Clock, the thermostat will follow your
settings for the Monday "Wake" time period until you reset the time and day.
Setting the fan
Press Fan to select On or Auto (toggle to re-select).
Auto : Fan runs only when the heating or cooling system is on. Auto is the
HOLD
most commonly used setting.
On: Fan is always on.
Note: Options may vary depending on your heating/cooling equipment.
Selecting system mode
M33852
Press System to select:
Heat: Controls only the heating system.
Cool: Controls only the cooling system.
Off: Heating/cooling systems are off.
Auto: Selects heating or cooling depending on the indoor temperature.
Em Heat (heat pumps with aux. heat): Controls auxiliary/emergency heat.
Compressor is off.
Note: Depending on how your thermostat was installed, you may not see
all system settings.
Adjusting program schedules
1 Press Set Clock/Day/Schedule, then Set Schedule.
2 Press or to set your Monday (Mon) Wake time, then press Next.
s t
3 Press or to set the temperature for this period, then press Next.
s t
4 Set time and temperature for the next time period (Leave). Repeat
Steps 2 and 3 for each time period.
5 Press Next to set time periods for the next day. Repeat Steps 2 through
4 for each day.
6 Press Done to save and exit.
Note: Make sure the thermostat is set to the system mode you want to
program (Heat or Cool).
or to set clock.
s t
or to select the day of week.
t
33-00306EFS-01