Lithonia Lighting TFX2 Directives D'installation page 2

READ AND FOLLOW THESE SAFETY INSTRUCTIONS!
• To reduce the risk of death, personal injury or property damage from fi re, electric
shock, falling parts, cuts/abrasions, and other hazards please read all warnings
and instructions included with and on the fi xture box and all fi xture labels.
• Before installing, servicing, or performing routine maintenance upon this
equipment, follow these general precautions.
• Installation, service and maintenance of luminaires should be performed by a
qualifi ed licensed electrician.
• Maintenance of the luminaires should be performed by person(s) familiar with
the luminaires' construction and operation and any hazards involved. Regular
fi xture maintenance programs are recommended.
• It will occasionally be necessary to clean the outside of the refractor/lens.
Refractor/lens should be washed in a solution of warm water and any mild, non-
abrasive household detergent, rinsed with clean water and wiped dry. Should
optical assembly become dirty on the inside, wipe refractor/lens and clean in
above manner, replacing damaged gaskets as necessary.
• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly
packed so that no parts should have been damaged during transit. Inspect to
confi rm. Any part damaged or broken during or after assembly should be
replaced.
• Recycle: For information on how to recycle LED electronic products, please
visit www.epa.gov.
• These instructions do not purport to cover all details or variations in equipment
nor to provide every possible contingency to meet in connection with installation,
operation, or maintenance. Should further information be desired or should
particular problems arise which are not covered suffi ciently for the purchaser's
or owner's purposes, this matter should be referred to Acuity Brands Lighting,
Inc.
WARNING
RISK OF ELECTRIC SHOCK
► Disconnect or turn off power before installation or servicing.
► Verify that supply voltage is correct by comparing it with the luminaire label
information.
► Make all electrical and grounded connections in accordance with the National
Electrical Code (NEC) and any applicable local code requirements.
► All wiring connections should be capped with UL approved wire connectors.
CAUTION
RISK OF INJURY
► Wear gloves and safety glasses at all times when removing luminaire from
carton, installing, servicing or performing maintenance.
► Avoid direct eye exposure to the light source while it is on.
WARNING
RISK OF BURN
► Allow lamp/fi xture to cool before handling. Do not touch enclosure, lens or light
source.
► Do not exceed maximum wattage marked on luminaire label.
► Follow all manufacturer's warnings, recommendations and restrictions including
but not limited to: driver type, burning position, mounting locations/methods,
replacement and recycling.
CAUTION
RISK OF FIRE
► Keep combustible and other materials that can burn, away from lamp/lens.
► Do not operate in close proximity to persons, combustible materials or
substances aff ected by heat.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF PRODUCT DAMAGE
► Never connect components under load.
► Do not mount or support these fi xtures in a manner that can cut the outer jacket
or damage wire insulation.
► Unless individual product specifi cations deem otherwise: Never connect an LED
product directly to a dimmer packs, occupancy sensor, timing device, or other
related control devices. LED fi xtures must be powered directly off a switched
circuit.
► Unless individual product specifi cations deem otherwise: Do not restrict fi xture
ventilation. Allow for some volume of airspace around the fi xture. Avoid
covering LED fi xtures with insulation, foam, or other material that will prevent
convection or cooling.
► Unless individual product specifi cations deem otherwise: Do not exceed fi xtures
maximum ambient temperature.
► Only use fi xture in its intended location.
► LED products are Polarity Sensitive. Ensure proper Polarity before installation.
► Electrostatic Discharge (ESD): ESD can damage LED fi xtures. Personal
grounding equipment must be worn during all installation or servicing of unit.
► Do not touch individual electrical components as this can cause ESD, shorten
lamp life, or alter performance.
► Some components inside the fi xture may not be serviceable. In the unlikely
event your unit may require service, stop using the unit immediately and contact
an ABL representative for assistance.
► Changes or modifi cations not expressly approved by Acuity Brands Lighting
could void the authority to operate the equipment.
► Always read the fi xtures complete installation instructions prior to installation
for any additional fi xture specifi c warnings.
This equipment has been tested and found to comply with the limits for a class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when used in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions
may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diff erent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
5-YEAR LIMITED WARRANTY
Register your warranty on www.acuitybrands.com/resources/warranty. Your
prompt product registration confi rms your right to the protection available under
the terms and conditions of your Lithonia Lighting warranty.
Failure to follow any of these instructions could void product warranties. For a
complete listing of product Terms and Conditions, please visit www.acuitybrands.
com. Acuity Brands Lighting, Inc. assumes no responsibilities for claims arising
out of improper or careless installation or handling of its products.
page 2