Lithonia Lighting TE Serie Directives D'installation

INSTALLATION
INSTRUCTIONS
Upon receipt of fixture and accessories
(packed separately) thoroughly inspect for
any freight damage which should be
brought to the attention of the delivery
carrier. Compare the catalog description
listed on the packing slip with the fixture
label on the outside of the housing to be
sure you have received the correct
merchandise.
TE/TX Series
Wet Location Housing
High Pressure Sodium,
Metal Halide and Mercury Vapor
For use with the following opticals:
A20 A165
A23 PA22C
A26 PA25ALE
PA25D A125
IMPORTANT SAFETY
INSTRUCTIONS
(For Your Protection, Read Carefully)
• This fixture must be wired in accordance
with the National Electrical Code and
applicable local codes and ordinances.
• Proper grounding is required to ensure
personal safety.
• Use approved connectors for all electrical
connections.
• ALL work should be done by a qualified
electrician.
• WARNING: NEVER disconnect any
component while power supply is engaged.
INDOOR H.I.D. LIGHTING
Read carefully before installing light fixtures. If you do not understand these instructions, please contact
your local Lithonia Lighting distributor before installing.
INSTALLATION: TE/TX Series Wet Location Housing
These fixtures are designed to mount easily onto a Lithonia Lighting pendant splice box (PSB).
The pendant splice box comes dissassembled in the fixture carton.
Housing
E17
E22
A30
GROUNDING NOTE: These fixtures must be grounded in accordance with NEC/CEC and applicable local
codes and ordinances.
WARNING: Check to be sure the proper fixture voltage lead has been selected to match the supply voltage.
Improper wiring may result in ballast failure and voids all warranties. NEVER perform maintenance or
cleaning while fixture is energized.
LAMP INSTALLATION
Prior to installing the lamp in the fixture, check to make sure the lamp is the correct type and wattage. Screw
the lamp securely into the socket, back it out one or two turns,then screw lamp back in, making sure it is
secure. This procedure properly seats lamp in the socket.
CAUTION: Observe lamp manufacturer's recommendations/restrictions on lamp operations, ballast type,
burning position, etc. If TE/TX fixture is equipped with QRS, remove the extension bracket prior to installing
optical.
NOTE: This instruction sheet explains housing installation. For Optical Assembly refer to instruction sheet
in reflector carton.
TROUBLESHOOTING
If this fixture fails to operate properly, check to make sure:
• The correct lamp is installed.
• The lamp is not faulty.
If all these variables have been checked and the fixture still does not operate properly, contact your
local Lithonia Lighting distributor.
Prior to Installation
Conduit
Feed
PSB
Cover
Plate
WL Plug/
Receptacle
• The line voltage at the fixture is proper.
SAVE THESE INSTRUCTIONS
1. Remove coverplate screws from pendent splice
box (PSB).
2. Attach PSB securely to 3/4" conduit, fitting, or
other approved wet location supporting means. A
locknut must be used between the PSB and
supporting conduit to insure that the fixture does
not vibrate loose.
3. Make supply connections. For multiple voltage
fixture, first determine correct line voltage. Then
select the proper fixture voltage lead, remove
crimped cap and connect to supply voltage lead.
Insulate all unused leads individually.
4. Insert spliced connections into PSB and reattach
cover.
For hook, cord and plug options:
1. Attach hook securely to approved support
ensuring that the hook latch closes.
2. If hardwiring to junction box,verify correct line
voltage. For multiple voltage fixture, voltage can
be selected and changed by removing the
coverplate screws from the pendent splice box
and selecting the proper fixture voltage leads.
Insulate all unused leads individually.
3. Verify that all receptacles, connectors and
junction boxes are rated for the environment in
which they will be utilized per all applicable local
and national codes.
• The fixture is wired correctly.
• The fixture is grounded correctly.
© 2001 Lithonia Lighting, Rev. 09/01
RJ5210153
TE-TX.PM65