Scheppach HM135B Traduction Des Instructions D'origine page 27

• Open the set screw (29) on the moveable stop
rail (28) and push the moveable stop rail (28) out-
wards.
• The moveable stop rail (28) must be locked in a
position far enough from the inner position that the
distance between the stop rail (28) and the saw
blade (7) is no more than 5 mm.
• Before making the cut, check that no collision
could occur between the stop rail (28) and the saw
blade (7).
• Tighten the set screw (29) again. (2x 8.6 + 8.7)
• Use the handle (13) to adjust the rotary table (16)
to the desired angle. The pointer (14) on the rota-
ry table (16) must match the desired angle on the
scale (15) on the fixed saw table (17).
• Tilt the locking lever (13) back up again to fix the
rotary table (16) in place.
• Cut as described under section 8.3.
8.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1,2,6,8)
The crosscut saw can be used to make mitre cuts of
0° - 45° in relation to the work face.
Important. To make miter cuts (inclined saw head),
the adjustable stop rail (28) must be fixed at the outer
position.
• Open the locking lever (29) for the adjustable stop
rail (28) and push the adjustable stop rail outwards.
• The adjustable stop rail (28) must be fixed far
enough in front of the innermost position that the
distance between the stop rail (28) and the saw
blade (7) amounts to a maximum of 5 mm.
• Before making a cut, check that the stop rail (28)
and the saw blade (7) cannot collide.
• Secure the locking lever (29) again.
• Move the machine head (5) to the top position.
• Fix the rotary table (16) in the 0° position.
• Loosen the set screw (22) and use the handle (1)
to angle the machine head (5) to the left, until the
pointer (20) indicates the desired angle measure-
ment on the scale (19).
• Re-tighten the fixing screw (22).
• Cut as described in section 8.3.
8.7 Mitre cut 0°- 45° and turntable 0°- 45°
(Fig. 1,2,6,9)
The crosscut saw can be used to make mitre cuts
to the left and right of 0°- 45° in relation to the work
face and, at the same time, 0° - 45° to the left or 0°
- 45° to the right in relation to the stop rail (double
mitre cut).
Important. To make miter cuts (inclined saw head),
the adjustable stop rail (28) must be fixed at the outer
position.
• Open the locking lever (29) for the adjustable stop
rail (28) and push the adjustable stop rail outwards.
• The adjustable stop rail (28) must be fixed far
enough in front of the innermost position that the
distance between the stop rail (28) and the saw
blade (7) amounts to a maximum of 5 mm.
• Before making a cut, check that the stop rail (28)
and the saw blade (7) cannot collide.
• Secure the locking lever (29) again.
• Move the machine head (5) to its upper position.
• Release the rotary table (16) by loosening the set
screw (26).
• Using the handle (13), set the rotary table (16) to
the desired angle (refer also to point 8.4 in this
regard).
• Re-tighten the set screw (26) in order to secure
the rotary table.
• Undo the locking screw (22) and use the handle
(1) to tilt the machine head (5) to the left until it co-
incides with the required angle value (in this con-
nection see also section 8.6).
• Re-tighten the fixing screw (22).
• Cut as described under section 8.3.
8.8 Limiting the cutting depth (Fig. 3)
• The cutting depth can be infinitely adjusted using
the screw (26). To do this loosen the knurled nut
on the screw (26). Turn the screw (26) in or out to
set the required cutting depth. Then re-tighten the
knurled nut on the screw (26).
• Check the setting by completing a test cut.
8.9 Sawdust bag (Fig. 2)
• The saw is equipped with a debris bag (21) for
sawdust and chips.
• Squeeze together the metal ring on the dust bag
and attach it to the outlet opening in the motor area.
• The debris bag (21) can be emptied by means of
a zipper at the bottom.
8.10 Changing the saw blade (Fig. 11-14)
Remove the power plug!
Important. Wear safety gloves when changing
the saw blade. Risk of injury!
• Swing up the machine head (5).
• Loosen the screw (f) of the flange cover so that it
is free to move.
• Press the release lever (3). Swing up the saw bla-
de guard (6) to the point where the recess in the
saw blade guard (6) is above the flange bolt (32).
• Insert the hexagonal key (c) in the flange bolt (32).
• Firmly press the saw shaft lock (4) and slowly ro-
tate the flange bolt (32) in clockwise direction. The
saw shaft lock (4) engages after no more than one
rotation.
• Now, using a little more force, slacken the flange
bolt (32) in the clockwise direction.
• Turn the flange screw (32) right out and remove the
external flange (33).
• Take the blade (7) off the inner flange (37) and pull
out downwards.
• Carefully clean the flange screw (32), outer flange
(33) and inner flange (37).
• Fit and fasten the new saw blade (6) in reverse
order.
• Important! The cutting angle of the teeth, in other
words the direction of rotation of the saw blade
(7) must coincide with the direction of the arrow
on the housing.
GB 27