OFFCAR 6UNICO Serie Instructions D'utilisation page 6

90FTE80RC
90FTE80LR
90FTE80LRC
MODEL SERIES 1100
H 900 mm
Power supply voltage: 3F/N/ ╧ AC400V
11FTE90L
11FTE90LC
MODEL DRAGONE
H 900 mm
Power supply voltage: 3F/N/ ╧ AC400V
DE722L
DE722LC
DE733L
DE733LC
MODEL STILE 1200
H 900mm H 270MM
Power supply voltage: 3F/N/ ╧ AC400V
80FTE12L - 80TFE12L
80FTE12LC - 80TFE12LC
80FTE12LR - 80TFE12LR
80FTE12LRC - 80TFE12LRC
80FTE12L - 80TFE12L
70FTE12L - 70TFE12L
70FTE12LC - 70TFE12LC
70FTE12LR - 70TFE12LR
70FTE12LRC - 70TFE12LRC
MODEL DIMENSIONS
SERIE 700 UNICO
SERIE 6 UNICO
W X D X H mm
U70FTE40L 400x730x900
U70FTE80L 800x730x900
U70FTE80LR 800x730x900
6UFTE35ML 350x630x285
6UFTE70ML 700x630x285
6UFTEMLR 700x630x285
Read the instructions contained in this handbook carefully as they give important advice concerning safety of installation,
use and maintenance. Keep this handbook for any further consultation by the various operators.
After having removed the packing, make sure the equipment is intact. In case of doubt, do not use the equipment and
contact professionally qualified staff.
Before connecting the equipment, make sure that the rating corresponds to that of electricity mains.
The equipment must only be used by staff trained in use.
Before carrying out cleaning and maintenance, disconnect the equipment from the electricity supply system.
Switch the equipment off in the case of a fault or malfunctioning. For any repairs only contact an authorised technical
service centre and request the use of original spare parts.
Failure to observe the above may jeopardise safety of the equipment.
Connection, installation of the system and appliances, ventilation and fumes extraction must be carried out according to
the manufacturer's instructions, by professionally specialised staff. The current regulations of the fire brigade must be
observed.
The electrical safety of this equipment is only ensured when it is correctly connected to an effective earthing system as
laid down by current electrical safety regulations.
This fundamental safety requirement has to be checked and, in case of doubt, an accurate check on the system by
professionally qualified staff requested. The manufacturer cannot be considered liable for any damage caused by failure
to earth the system.
This equipment must only be used for the purpose for which it was specifically designed.
Do not wash the equipment with direct, high pressure jets of water.
Do not obstruct the openings or vents for extraction or release of heat.
So as to avoid the risk of rust or chemical attack in general, the stainless steel surfaces have to be kept properly clean.
900x900 761x756
900x900 761x756
900x900 761x756
DIMENSIONS PLATE
W x D mm mm
900x1100 761x875
900x1100 761x875
DIMENSIONS PLATE
W x D mm mm
1100x700 1092x558
1100x700 1092x558
1650x700 1642x558
1650x700 1642x558
DIMENSIONS PLATE
W x D mm mm
1200X900 1150x756
1200X900 1150x756
1200X900 1150x756
1200X900 1150x756
1200X900 1150x756
1200X730 1150x570
1200X730 1150x570
1200X730 1150x570
1200X730 1150x570
DIMENSIONS PLATE
W X D mm
360x570
755x570
755x570
340x510
680x510
680x510
1. GENERAL INSTRUCTIONS
Scored chromium-plated
Half smooth – half scored
2 1
/ smooth - / scored chromium-plated
3 3
COMPOSITION
Power cable: 5 x 2,5 mm
Smooth chromium-plated
TOP COMPOSITION
Power cable: 5 x 4 mm
Smooth chromium-plated
Smooth chromium-plated
COMPOSITION
Power cable: 5 x 4 mm
Smooth chromium-plated
2
/ smooth -
3
2 / smooth - 1 / scored chromium-plated
3 3
Smooth chromium-plated
2
/ smooth -
3
2 1
/ smooth - / scored chromium-plated
3 3
Total Kw
Power supply
3F/N/ ╧ AC400V
4,8
3F/N/ ╧ AC400V
9,6
3F/N/ ╧ AC400V
9,6
1F/N/ ╧ AC230V
3,6
1F/N/ ╧ AC230V
7,2
1F/N/ ╧ AC230V
7,2
6
TOP
2
Smooth
2
Smooth
Smooth
TOP
2
Smooth
1
/ scored
3
Smooth
Smooth
1
/ scored
3
POWER RATING
Nr x mm
12
12
12
POWER
KW
10
10
POWER
KW
15
15
20
20
POWER
KW
18
18
18
18
18
15
15
15
15
2
5x1,5
5x2,5
5x2,5
3x2,5
3x4
3x4