Publicité
Les discussions sur la poignée de serrage sont un sens de fil Gaucher, tournant vers la droite aurait desserrer l'assemblage et en
tournant dans le sens antihoraire serait serrer l'ensemble. La poignée de serrage est à ressort, de sorte que vous aurez besoin pour
soulever et tourner tout l'ensemble de la poignée de serrage quand repositining comme pour être un lecteur de clé à cliquet.
Pour desserrer l'Assemblée pivotant de la plaque
1. Soulevez la pince poignée Assemblée, tourné dans le
sens antihoraire et la libération. Cela repositionner le
levier pour plus de mouvement.
2. Avec la pince poignée Assemblée maintenant, tirez la
pince poignée Assemblée aiguilles d'une montre. Avec ce
qui est un fil de gaucher, ce sera desserrer l'assemblage.
3. Si plus de Voyage est nécessaire, soulevez la poignée
de serrage, tourner dans le sens antihoraire et la libération.
4. Tirez à nouveau l'ensemble poignée de serrage dans
le sens horaire. Cette quantité de mouvement devrait être
suffisant pour repositionner l'exercice, plus de mouvement
que cela peut causer l'aimant de se désengager de la base
de forage.
1
WARNING:
AVERTISSEMENT:
Work Area
Keep your work area clean and well lit. Cluttered benches and
dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
Keep bystanders, children, and visitors away while operating a
power tool. Distractions can cause you to loose control.
Electrical Safety
Grounded tools must be plugged into an outlet properly in-
stalled and grounded in accordance with all codes and ordi-
anaces. Never remove the ground prong or modify the plug in
any way. Do not us any adapter plugs. Check with a qualified
electrician if you are in doubt as to whether the outlet is prop-
erly grounded. If the tools should electrically malfunction or break-
down, grounding is provides a low resistance path to carry electricity
away from the user.
Avoid body contact with grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of
electric shock if your body is grounded.
Don't expose power tools to rain or wet conditions. Water enter-
ing a power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord to carry the tools or
pull the plug from an outlet. Keep cord away from heat, oil, sharp
edges or moving parts. Replace damaged cords immediately.
Damaged cords increase the risk of eletric shock.
When operating a power tool outside, use an outdoor extension
cord marked "W-A" or "W"; These cords are rated for outdoor use
and reduce the risk of electrical shock.
Personal Safety
Stay alert, watch what you are doing and use common sense
INSTRUCTIONS BASE PIVOTANTE
2
Important Safety Instructions
Read and understand all instructions. Failure to follow all instructions listed below,
Poignée de serrage doivent être bien serrés avant de découper des trous
may result in electrical shock, fire and/or serious personal injury.
Des dommages matériels ou des blessures pourraient survenir
Pour Serrer l'Assemblée pivotant de la plaque
1. Soulevez la pince poignée Assemblée, tourné dans le sens
antihoraire et la libération. Cela repositionner le levier pour
plus de mouvement.
2. Avec la pince poignée Assemblée maintenant, tirez la pince
poignée Assemblée aiguilles d'une montre. Avec ce qui est
un fil de gaucher, ce sera desserrer l'assemblage.
3. Si plus de Voyage est nécessaire, soulevez la poignée de
serrage, tourner dans le sens antihoraire et la libération.
4. Tirez à nouveau l'ensemble poignée de serrage dans
le sens horaire. Cette quantité de mouvement devrait être
suffisant pour repositionner l'exercice, plus de mouvement
que cela peut causer l'aimant de se désengager de la base
de forage.
1
Use safety equipment. Always wear eye production. Dust
mask, non-skid safety shoes, hard hat, or hearing protection
must be used for appropriate conditions.
Always use safety chain. Mounting can release.
Tool Use and Care
Use clamps or other practical way to secure and support
the work piece to a stable platform. Holding the work by
hand or against your body is unstable and may lead to loss of
control.
Do not force tool. Use the correct tool for your application.
The correct tool will do the job better and safer at the rate for
which it is designed.
Do not use tool if switch does not turn it on or off. Any
tool that cannot be controlled with the switch is dangerous and
must be repaired.
Disconnect the plug from the power source before making
any adjustments, changing accessories, or storing the
tool. Such preventive safety measures reduce the risk of start-
ing the tool accidentally.
Store idle tools out of reach of childern and other
untrained persons. Tools are dangerous in the hands of
untrained users.
Maintain tools with care. Keep cutting tools sharp and
clean. Properly maintained tools, with sharp cutting edges are
less likely to bind and are easier to control.
Check for misalignment or binding of moving parts, break-
age of parts, and any other condition that may affect the
tools operation. If damaged, have the tool serviced before
using. Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manu-
18
facturer for your model. Accessories that may be suitable for
one tool, may become hazardous when used on another tool.
2
Publicité
