Publicité
Les langues disponibles
Les langues disponibles
English
nOTE: Avoid cross threading when installing the hose. Cross
threading will cause leaks.
1. To connect the high pressure hose
grip
5
, thread the hose collar
coupler
32
.
2. To connect the high pressure hose to the pressure
washer unit
8
, thread the hose collar
pressure water outlet
Attaching Garden Hose (Fig. H)
nOTE: Before connecting the garden hose to the pressure
washer unit, run water through the garden hose for thirty
seconds to clear any debris from inside the garden hose.
1. To connect a garden hose to the
pressure washer unit
garden hose
35
inside the water intake
2. Securely tighten the garden hose by hand.
nOTE: Always disconnect the garden hose after usage.
Attaching Nozzles (Fig. I)
DANGER: Risk of fluid injection. Do not direct
discharge stream toward persons, unprotected skin,
eyes or any pets or animals. Serious injury will occur.
WARNING: Flying objects could cause risk of serious
injury. DO NOT attempt to change nozzles while
pressure washer is running. Turn pressure washer unit
OFF before changing nozzles.
1. To connect a nozzle to the spray wand
connect collar
3
toward the spray wand and insert the
appropriate nozzle.
2. Release the quick connect collar to lock the nozzle in place.
3. Give the nozzle a firm tug after the quick connect collar
has locked into place to ensure the nozzle is locked
into place.
nOTE: The nozzles listed below might not be included with your
pressure washer but are available for purchase at an additional cost.
Common Spray Nozzles
15 ° Orange Nozzle
25 ° Green Nozzle
40 ° White Nozzle
Black Turbo Nozzle
Attaching High Pressure Foam Cannon
(Fig. J)
1. To connect the high pressure foam cannon
the spray wand
2
, pull the quick connect collar
toward the spray wand and insert the high pressure
foam cannon
26
.
2. Release the quick connect collar
pressure foam cannon
8
1
to the handle
33
onto the inlet
34
onto the high
18
.
8
, place the end of the
17
.
2
, pull the quick
Common Applications
For brick or masonry.
For vinyl siding.
For automotive washing.
For abrasive cleaning.
26
to lock the high
3
in place.
26
3. Give the high pressure foam cannon
the quick connect collar has locked into place to ensure
the high pressure foam cannon
4. To adjust the rate of foam, rotate the pressure
control knob
foam cannon
for more foam.
nOTE: The soap bottle should be positioned underneath the
spray wand. Do not position the high pressure foam cannon
above the spray wand as this will lead to soap dripping
on the spray wand. The spray tip on the high pressure
foam cannon
Removing High Pressure Foam Cannon
from Storage (Fig. A)
Always completely empty the high pressure foam cannon
before storing.
1. To remove the high pressure foam cannon
built in storage space in the pressure washer unit, grasp
the high pressure foam cannon
pull it out and away from the pressure washer unit.
2. To place the high pressure foam cannon
storage slot, press the high pressure foam cannon
firmly into the storage slot until it snaps into the built in
storage space in the pressure washer unit.
3. Ensure that foam cannon
position by gently tugging on the foam cannon
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Proper Hand Position (Fig. K)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the spray handle
grip
5
and the other hand on the spray handle
Test Ground Fault Circuit Interrupter (GFCI)
Before Each Use (Fig. A)
This pressure washer is provided with a ground fault circuit
interrupter (GFCI) built into the plug of the power supply
to
cord. This device provides additional protection from the risk
3
of electric shock.
1. Plug the Ground Fault Circuit Interrupter (GFCI)
working grounded outlet.
2. The indicator at the top of the GFCI should turn green
when product is ready to use.
3. Press the "TEST" button (bottom). The green indicator
should disappear.
26
36
on the top of the high pressure
26
counterclockwise for less or clockwise
26
rotates for vertical or horizontal application.
26
26
is secured into the storage
26
a firm tug after
is locked into place.
26
26
from the
with one hand and
26
into its
26
26
.
4
.
21
into a
Publicité
