Publicité
Les langues disponibles
Les langues disponibles
OPERATION
Mount the tank (2) in its seat. To ensure correct function, press down well the tank.
Fill the tank (2) with water without exceeding level MAX, then close with the lid(1).
WARNING: Use fresh natural water, do not use hot or sparkling water, or other liquids.
MOUNT FILTER IN THE FILTER HOLDER
The filters are equipped with a safety system that avoids accidental falling of the
filter. To mount and dismount a filter, you have to align the parts identified with A
(filter) and B (filter holder) in the picture on the side.
To mount a filter in the filter holder
-
Take the filter grabbing in correspondence of the part A.
-
Insert in the filter holder (21) the part of filter opposite to the part A.
-
Lower the filter into the filter holder by aligning the parts A and B.
To dismount the filter, align the parts A and B and pull the filter upwards.
MAKE COFFEE WITH POWDER
- Insert the plug in the power socket and press button (7) to switch on. The lights of buttons
twinkle to indicate that the appliance is heating, and then they stay on when the appliance
is ready.
- Select the desired filter, one or two cups (18 or 19), and insert in the filter holder (21).
- Pour 1 cup (17) not filled in case of 1 cup filter and press slightly with presser.
- Pour 2 cups (17) not filled in case of 2 cups filter and press slightly with presser.
- Mount the filter holder (21) in its seat (13). Insert the filter holder in correspondence of symbol
rotate clockwise to the symbol . Place one or 2 coffee cups under the spout (22).
- Press button (9 -
- The button twinkles. There is a short phase of water loading, then the coffee comes out from spouts (22).
- Once the desired quantity has been reached, press the flashing button again to stop dispensing.
WARNING: do not remove the filter holder during function. At the end of erogation, wait 10 seconds before
removing the filter holder. Remove slowly the filter holder to avoid splashing.
- At the end of dispensing, the lights remain on and you can make another coffee.
- If use is finished, turn off the machine with the button (7).
WARNING: after use, do not leave the filter holder (21) inserted in its seat (13) in order
to not damage the gasket present in the filter holder seat.
MAKE COFFEE WITH PODS
- Insert the plug in the power socket and press button (7) to switch on. The lights of buttons twinkle to
indicate that the appliance is heating, and then they stay on when the appliance is ready.
- Select the POD pod filter (20), and insert in the filter holder (21).
- Insert a pod in the filter, and press it inside with your fingers. The pod must be well centered and pushed
down well. If the external paper parts protrude from the filter, fold them inwards.
WARNING: If the pod is not inserted correctly, or if the external paper parts are not folded well, the filter
holder may not tighten, and drops may come out of the filter holder.
- Mount the filter holder (21) in its seat (13). Insert the filter holder in correspondence of symbol
rotate clockwise to the symbol .
- Place one coffee cup under the spout (22). Press the button (9 -
- The button twinkles. There is a short phase of water loading, then the coffee comes out from spouts (22).
- Once the desired quantity has been reached, press the flashing button again to stop dispensing.
WARNING: do not remove the filter holder during function. At the end of erogation, wait 10 seconds before
removing the filter holder. Remove slowly the filter holder to avoid splashing.
- At the end of dispensing, the lights remain on and you can make another coffee.
- When removing the filter holder, the pod may remain attached to the seat of the filter holder (13). To
remove it, tilt the filter holder down, or remove it gently with a knife.
- If use is finished, turn off the machine with the button (7).
) for one cup of espresso or the button (10 -
) for two cups.
).
and
and
17
Publicité
