Publicité
Liens rapides
CONTACT US FIRST
CONTACT US FIRST
sauder.com
sauder.com
sauder.com
BEFORE MAKING ANY RETURNS TO THE STORE.
BEFORE MAKING ANY RETURNS TO THE RETAILER.
sauder.com/service
Visit
Prefer the phone? Give us a ring at
Customer Service is available Monday-Friday - 8:30 a.m. to 5 p.m. EST (except holidays)
Library Base
Costa Collection | Model 428192
Sauder.com
Share your journey!
to order replacement parts, view video assembly tips, or chat with a live rep.
1-800-523-3987
.
Here's one for
the books.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-22
Français pg 23-25
Español pg 26-28
Lot # 548099
Purchased: __________________
10/26/20
Publicité
Manuels Connexes pour Sauder Library Base 428192
Sommaire des Matières pour Sauder Library Base 428192
- Page 1 CONTACT US FIRST CONTACT US FIRST sauder.com sauder.com sauder.com BEFORE MAKING ANY RETURNS TO THE STORE. BEFORE MAKING ANY RETURNS TO THE RETAILER. sauder.com/service Visit to order replacement parts, view video assembly tips, or chat with a live rep. 1-800-523-3987 Prefer the phone? Give us a ring at Customer Service is available Monday-Friday - 8:30 a.m.
- Page 2 RIGHT FRONT LEG (1) material. Color may vary.) BOTTOM MOLDING (1) BACK (1) LEFT REAR LEG (1) D509 DRAWER SIDE (2) TOP (1) LEFT FRONT LEG (1) D510 DRAWER BOX FRONT (2) DOOR (2) RIGHT REAR LEG (1) Page 2 428192 www.sauder.com/service...
- Page 3 Part Identification D509 D510 D510 D509 www.sauder.com/service 428192 Page 3...
- Page 4 BLACK 1/2" FLAT HEAD SCREW - 8 BLACK 7/8" LARGE HEAD SCREW - 3 30S BLACK 1-9/16" FLAT HEAD SCREW - 6 BLACK 1-1/8" MACHINE SCREW - 2 BLACK 9/16" FLAT HEAD SCREW - 4 SILVER 1-1/2" MACHINE SCREW - 2 Page 4 428192 www.sauder.com/service...
- Page 5 Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. STOP å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (37F) into the large holes in the ENDS (A and B) If you purchased and BOTTOM (E).
- Page 6 Push twelve HIDDEN CAMS (1F) into the ENDS (A and B). Some assembly (and snacks) required. Arrow (12 used) Arrow Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. Page 6 428192 www.sauder.com/service...
- Page 7 Step 3 å Turn twelve CAM SCREWS (8F) into the LEGS (H, O, P, and S). (12 used) www.sauder.com/service 428192 Page 7...
- Page 8 NOTE: If the MOLDING comes up off of the SCREWS, the SCREWS and onto the ENDS. remove it and slide it on again. The MOLDINGS should be even on both edges of the ENDS. Shoulder BLACK 9/16" FLAT HEAD SCREW (4 used in this step) Page 8 428192 www.sauder.com/service...
- Page 9 Fill the holes 1/4 to 1/2 full with GLUE. These surfaces should be even. Edge with TWIST-LOCK® End without hole FASTENERS S u r f a c H I D D E N i t h These surfaces should be even. End without hole www.sauder.com/service 428192 Page 9...
- Page 10 Fill the holes 1/4 to 1/2 full with GLUE. These surfaces should be even. End with hole S u r f a c H I D D E N i t h Edge with TWIST-LOCK® FASTENERS These surfaces should be even. End with hole Page 10 428192 www.sauder.com/service...
- Page 11 NOTE: The EXTENSION SLIDES will be used later for the DRAWER. Push the black lever in and pull the SLIDE from the RAIL. GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Open end Open end www.sauder.com/service 428192 Page 11...
- Page 12 Slide the BOTTOM MOLDING (D) onto the notched edge of the BOTTOM (E). Notched edge Slide the BOTTOM MOLDING (D) onto the notched edge. These surfaces should be even. The groove is closer to this edge. Page 12 428192 www.sauder.com/service...
- Page 13 Tighten four TWIST-LOCK® FASTENERS. Do not stand the unit upright without the BACK fastened. The unit may collapse. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part.
- Page 14 But definitely makes for a sturdier Library Base that’ s easier to assemble and friendlier to the environment. h o l i t h f a c S u r These small holes must be here. Page 14 428192 www.sauder.com/service...
- Page 15 SILVER 1-1/8" FLAT HEAD SCREWS (10S). your drink. å NOTE: Do not overtighten the SCREWS into the TOP. SILVER 1-1/8" FLAT HEAD SCREW (3 used in this step) Hidden part using recycled material. Color may vary. www.sauder.com/service 428192 Page 15...
- Page 16 Push on opposite corners of your unit if needed to make BACK fastened. The unit may collapse. it "square". å Fasten the BACK (I) to your unit using the NAILS (1N). NAIL (32 used in this step) Page 16 428192 www.sauder.com/service...
- Page 17 Step 13 å Fasten two HINGES (14H) to each DOOR (K). Use eight BLACK 1/2" FLAT HEAD SCREWS (11S). BLACK 1/2" FLAT HEAD SCREW (8 used in this step) www.sauder.com/service 428192 Page 17...
- Page 18 Fasten a KNOB SET (136K) to the DOOR (K). Use a screw BLACK 1-1/8" MACHINE SCREW (21S). å Repeat this step for the other DOOR (K). å Hinge See the next step for DOOR adjustments. 136K BLACK 1-1/8" MACHINE SCREW (2 used for the KNOBS) Page 18 428192 www.sauder.com/service...
- Page 19 To adjust the DOORS in or out (depth), loosen the mounting screw one turn and move the DOORS in or out, as needed. Tighten the mounting screw after making adjustments. Mounting screw (depth) Adjusting screw (horizontal) (vertical adjustment) www.sauder.com/service 428192 Page 19...
- Page 20 Fasten the other DRAWER BOX FRONT (D510) to the Turn the drawer over and fasten the DRAWER BRACE (L) DRAWER SIDES (D509). Use two BLACK 1-9/16" FLAT to the DRAWER BOX FRONTS (D510). Use two BLACK HEAD SCREWS (30S). 1-9/16" FLAT HEAD SCREWS (30S). Page 20 428192 www.sauder.com/service...
- Page 21 BLACK 7/8" LARGE HEAD SCREW (3 used in this step) D509 D510 Open end D509 136K 136K SILVER 1-1/2" MACHINE SCREW BROWN 7/16" LARGE HEAD SCREW (2 used for the KNOB SETS) (4 used for the EXTENSION SLIDES) www.sauder.com/service 428192 Page 21...
- Page 22 NOTE: Please read the back pages of the instruction booklet for important safety information. å This completes assembly. Clean with a damp cloth. Wipe dry. And to celebrate, why not share your success story at sauder.com or (4 used) Page 22 428192 www.sauder.com/service...
- Page 23 DESCRIPTION QUANTITÉ conserver le livret pour future référence. Pour EXTRÉMITÉ DROITE ..........1 (ENSEMBLE DE GLISSIÈRE ILLUSTRÉ À PART) contacter Sauder en EXTRÉMITÉ GAUCHE ..........1 GLISSIÈRE D'EXTENSION ........2 ce qui concerne cet élément, faire référence B40 FOND DE TIROIR ............1 COULISSE D'EXTENSION ........2 au numéro de lot et...
- Page 24 Pour commencer l'assemblage, enfoncer une FIXATION EN BOIS (15F) dans les trous. Nettoyer l'excès de COLLE. TWIST-LOCK® SAUDER (37F) dans les gros trous des EXTRÉMITÉS (A et B) et le DESSOUS (E). REMARQUE : S’ a ssurer de positionner les pièces exactement comme il l’est indiqué.
- Page 25 Ceci complète l'assemblage. Nettoyer avec un tissu Fixer l'ENSEMBLE DE BOUTONS (136K) à la PORTE (K). Utiliser humide. Essuyer. une VIS À MÉTAUX 28 mm NOIRE (21S). Répéter cette étape pour l'autre PORTE (K). Voir l'étape suivante pour réglages des PORTES. www.sauder.com/service 428192 Page 25...
- Page 26 RIEL DE EXTENSIÓN ..........2 EXTREMO IZQUIERDO ..........1 necesita ponerse en CORREDERA DE EXTENSIÓN ......2 B40 FONDO DE CAJÓN ............1 contacto con Sauder en cuanto a esta unidad, EXCÉNTRICO ESCONDIDO ......12 MOLDURA DE EXTREMO ........2 refiérase al número 37F SUJETADOR TWIST-LOCK®........8 MOLDURA DE FONDO..........1...
- Page 27 1/4 a 1/2 con PEGAMENTO (177M). A continuación, inserte Para comenzar el ensamblaje, empuje un SUJETADOR dos PASADORES DE MADERA (15F) dentro de los agujeros. Quite TWIST-LOCK® SAUDER (37F) en los agujeros grandes de los el exceso de PEGAMENTO. EXTREMOS (A y B) y del FONDO (E).
- Page 28 TORNILLO NEGRO PARA METAL de 28 mm (21S). Esto completa el ensamblaje. Limpiar con un trapo húmedo. Repita este paso para la otra PUERTA (K). Seque con un paño. Consulte el próximo paso para ajustar la PUERTA. Page 28 428192 www.sauder.com/service...
- Page 29 à mortelles. Les téléviseurs peuvent être un téléviseur. cet effet. particulièrement lourds. De plus, le poids et l’emplacement du tube image ont tendance à rendre les téléviseurs instables et enclins à tomber vers l’ a vant. www.sauder.com/service 428192 Page 29...
- Page 30 Además, el peso y la ubicación del tubo de imagen tienden a causar la inestabilidad de televisores y propensa a volcarse hacia adelante. Page 30 428192 www.sauder.com/service...
- Page 31 à compter de la date d'achat la première fois et qui sont signalés à Sauder dans les limites de couverture de la contre tout défaut de matériaux ou de fabrication des composantes de mobilier Sauder.
- Page 32 BEFORE MAKING ANY RETURNS TO THE RETAILER. So, how did it go? Dear Valued Customer: Thanks so much for choosing Sauder® furniture. I hope the Set a world record for speed? purchase and assembly process was a positive experience Feeling good about yourself? and you feel good about the furniture you just built.