Publicité
Application
Operation is possible in conjunction with:
- Pressurized storage heaters
- Thermally controlled instantaneous heaters
- Hydraulically controlled instantaneous heaters
Operation with low-pressure storage heaters
(displacement water heaters) is not possible.
Technical data
• Max. flow
• Flow pressure
- min.
- recommended
- greater than 72.5 psi, fit with pressure reducing valves
• Max. operating pressure
• Test pressure
• Temperature
- max. (hot water inlet)
• Water connection
Note
Major pressure differences between cold and hot water supply
should be avoided.
Installation
See dimensional drawing on page 1.
Flush pipes thoroughly!
Side valves, see fig. [1] and [2].
• Valve with a groove on the top edge of the headpart (A) and
in addition marked with blue tape should be mounted on the
right (cold water) side, see fold-out page III, fig. [1].
• Valve without a groove on the top edge of the headpart (A)
and in addition marked with red tape should be mounted on
the left (hot water) side.
1. Screw the mounting set (B) to the bottom of the thread of the
side valve (C).
Make sure that the rubber washer (B1) is on the top of the
fiber washer (B2).
2. Insert the side valve (C) through the basin hole from below.
3. Place the escutcheon O-ring (D1) on the basin and screw
down the escutcheon (D) until it stops.
4. Screw the cap (E) down to the escutcheon (D).
5. Tighten the mounting set (B) from below to secure the valve.
6. Close the headparts (clockwise for the hot side and counter-
clockwise for the cold side).
Install the handle (F) or lever (G), sold seperatly, to the
stem of the headpart (A) and be sure that the lever points
away from the spout.
7. Screw the brass nut (G1) into the cap (E) until tight.
Hand tighten only!
8. Screw the ring (G2) to cover the brass nut (G1).
All manuals and user guides at all-guides.com
English
8.3 L/min or 2.2 gpm/60 psi
7.25 psi
14.5 - 72.5 psi
145 psi
232 psi
176 °F
cold - Right hand
hot - Left hand
Spout, see fig. [2] to [4].
1. Place the O-ring (I) and the escutcheon (H1) on the basin,
see fig. [2].
2. Insert the spout (H) through the escutcheon (H1) and basin.
3. Place the gasket (J) against the bottom of the basin and
fasten with the flange (K) and nut (K1). Tighten nut (K1) with
a 13mm socket wrench.
4. Connect flexible hoses (L) from spout connection tee to the
side valves, see figs. [3] and [4].
Mount lift rod and pop-up drain, see fig. [3] and [5].
1. Insert the lift rod (M) through the spout and screw on the
lower lift rod (N), see fig. [3].
The connector is at the lower lift rod (N).
For 18 086 VP0 see also fig. [5].
2. Fit pop-up drain (28 957), see page 2.
Ensure that flange of pop-up drain is sealed.
Connect wideset
Connect the side valves to the water supply. Insure the
supplied washers are used for all connections.
The cold water supply should be connected on the right side
valve (marked blue) and the hot water supply to the left valve
(marked red).
Open cold and hot-water supply and check connections
for watertightness!
Maintenance
Inspect and clean all parts, replace as necessary and grease
with special grease.
Shut off cold and hot water supply.
I. Ceramic headpart, see fig [6].
1. Remove handle (F) or lever (G) and cap (E).
2. Unscrew the ceramic headpart (A) using a 17mm wrench.
3. Change complete ceramic headpart (A).
Observe the different replacement part numbers of the
headparts, see page 2.
II. Flow regulator, see page 2.
Unscrew and clean flow regulator (13 990).
Assemble in reverse order.
Replacement parts, see page 2 ( * = special accessories).
Care
Instructions for care of this faucet will be found in the Limited
Warranty supplement.
4
Publicité
