Hotpoint Ariston FZ 101 P.1/HA Mode D'emploi page 17

Electrical connection
 Ovens equipped with a three-pole power supply
cable are designed to operate with alternating
current at the voltage and frequency indicated on
the appliance data plate (see below).
.itting the power supply cable
Connecting the supply cable to the mains
Install a standardised plug corresponding to the
load indicated on the data plate (see table).
The appliance must be directly connected to the
mains using an omnipolar circuit-breaker with a
minimum contact opening of 3 mm installed between
the appliance and the mains. The circuit-breaker
must be suitable for the charge indicated and must
comply with current electrical regulations (the
earthing wire must not be interrupted by the circuit-
breaker). The supply cable must be positioned so
that it does not come into contact with temperatures
higher than 50°C at any point.
 The installer must ensure that the correct electrical
connection has been made and that it is fully
compliant with safety regulations.
Before connecting the appliance to the power
supply, make sure that:
• The appliance is earthed and the plug is compliant
with the law.
All manuals and user guides at all-guides.com
1. Open the terminal
board by inserting a
screwdriver into the
side tabs of the cover.
Use the screwdriver as
a lever by pushing it
down to open the cover
(see diagram).
2. Loosen the cable
clamp screw and
remove it, using a
screwdriver as a lever
(see figure).
3. Remove the wire
contact screws L-N-
, then fasten the wires
under the screw heads,
respecting the colour
code: Blue (N), Brown
(L) and Yellow-Green
Verde ( ).
• The socket can withstand the maximum power of
the appliance, which is indicated on the data
plate (see below).
• The voltage is in the range between the values
indicated on the data plate (see below).
• The socket is compatible with the plug of the
appliance. If the socket is incompatible with the
plug, ask an authorised technician to replace it.
Do not use extension cords or multiple sockets.
 Once the appliance has been installed, the power
supply cable and the electrical socket must be
easily accessible.
 The cable must not be bent or compressed.
The cable must be checked regularly and replaced
by authorised technicians only (see Assistance).
 The manufacturer declines any liability should
these safety measures not be observed.
T A B L E O . C H A R A C T ER IS T IC S
w id th 43 .5 c m
D im ensio ns h e ig h t 3 2 c m
d e p th 40 c m
V o lum e 5 6 l
w id th 43 .5 c m
D im ensio ns * h e ig h t 3 2 c m
d e p th 41 .5 c m
V o lum e * 5 8 l
v o lta g e : 2 2 0 -2 40 V ~ 50 /6 0 H z
Ele ctrical
m a x im u m p o w e r a bs o rbe d
con nectio ns
2 80 0 W
D ire c tiv e 2 0 0 2 /40 /E C o n th e
la b e l o f e le c tric o ve n s .
R e g u latio n E N 5 0 3 0 4
EN ER G Y L A B E L **
D e c la re d e n e rg y
c o n s u m p tio n fo r .o rc e d
c o n v e c tio n C la s s
– h e a tin g m o d e :
T h is a p p lian c e c o n fo rm s to
th e fo llo w in g E u ro p ea n
E c o n o m ic C o m m u n ity
d ire c tiv e s : 7 3 /23 /E E C da te d
1 9/0 2 /73 (L o w V o lta g e ) a n d
s u b s e q u e n t a m e n d m e n ts -
89/3 3 6/E E C d a te d 0 3 /0 5 /89
(E le c tro m a g n e tic
C o m p a tib ility ) a n d
s u b s e q u e n t a m e n d m e n ts -
93 /68 /E E C d a te d 2 2 /0 7/93
a n d su b s e q u e n t
a m e n d m e n ts .
2 0 0 2 /96/E E C
* W ith g lass pan el fitted to the insid e o f th e d oor
** W ith out rem ov able guid e rails
GB
G ra tin
17