Power Requirements; Start-Up Instructions; Operating Instructions - Nordic Impulse Manuel Du Propriétaire

POWER INSTALLATION INSTRUCTIONS
Permanently connected installation instructions
Electrical installation should be performed by a qualified licensed electrician.
1. Remove cabinet service panel. The panel is secured with pan
head Phillips screws.
2. Remove system controller cover.
3. If spa was manufactured with a cord.
a. Disconnect cord wires from terminal TB1 and
ground wire from ground bar.
b. Loosen cord strain relief.
c. Remove cord.
d. Remove stain relief.
4. Drill hole for conduit through bottom or side of spa.
WARNING: DO NOT CONNECT POWER UNTIL TUB IS FILLED COMPLETELY WITH WATER!
Your Hot Tub is designed to provide optimum performance when
connected to the maximum electrical service. The listing below will show
the various options and performance levels available on your hot tub.
A new GFCI must be used for your Hot Tub installation. Do not use
an existing breaker (GFCI), as its condition is unknown.
Omni, Cottage,
Bella, Impulse,
Impulse DP
AMERICAS 60Hz 120v/240v
Circuit Breaker 15A/50A
Number of Wires 3/4
1. Clean tub of all debris.
2. Use a garden hose to fill your hot tub through the empty filter
canister (to avoid air pockets during filling) to the appropriate
level of a minimum 2 inches (5.08cm) over the filter skimmer.
3. DO NOT USE WATER THROUGH A WATER SOFTENER.
4. Locate the shut-off T-valves. Make sure they are in the up or
open position. (See page 7)
5. Check heater and pump unions. Occasionally during
shipping these become loosened. A simple tightening of
these (if necessary) will do, being careful not to over tighten.
(See page 7)
6. Once water has reached correct level, turn power on to the
hot tub.
7. To activate jets and to purge air from the pump, press/push jet
button located on the top side control. A second press/push
Whirlpool Diverter Jet(s):
Your hot tub (except Omni™) is equipped with at least one
Whirlpool Diverter jet (2, 3, or 4 position), located on filter wall on
most models. These jets when turned will divert water to different
groups of jets. Each position is reached with a 90 degree turn of the
whirlpool jet face. Always turn the collar of the diverter jet clockwise
when possible. Remember, turning your diverter will affect the flow
of water to different seat jets. Adjust to suit your personal needs.

POWER REQUIREMENTS

Escape, Escape R Escape Premium, Escape
Sport, Crown II, Premium R, Crown XL,
Warrior XL, Rendezvous Royal,
D'Amour, Retreat, Encore Premium,
Encore Encore SE, Retreat SE
120v/240v 240v
20A/50A 50A
3/4

START-UP INSTRUCTIONS

OPERATING INSTRUCTIONS

5. Secure conduit at system controller box.
6. Connect hot and neutral wires to corresponding terminals TB1.
Connect ground wire to grounding bar on the outside of box by
running it though hole marked for ground wire.
7. Voltage selection for North American 60 Hz systems.
a. 120V installation. Attach jumper to J11 and J32. A
jumper wire is supplied in a bag attached to the back or
side of controller. Switch DIP switch A10 to on (up).
b. 240V installation. Remove J11 to J32 jumper if installed.
Switch DIP switch A10 to off (down).
8. Attach system controller cover.
9. Attach cabinet service panel.
EUROPE 50Hz
Circuit Breaker
Number of Wires
On all systems, your Hot Tub must be connected to a dedicated
circuit breaker that is not shared with any other equipment.
4 DO NOT USE EXTENSION CORDS OF ANY KIND.
will put the pump on high speed. Repeat this process until
water flows from the jets. When the jets are working, set the
pump to low speed. (See page 9 or 10)
8. Some start-up chemicals will be needed; please see your
dealer for recommendations.
9. Set the temperature located on the top side control (See page 9
or 10) to the desired setting. The heater will shut off when the
water temperature reaches the set temperature.
10. Place the hot tub cover on tub. Keeping the cover on the
hot tub when the tub is not in use will help minimize
operating costs.
11. The time it will take for the water temperature to reach the
desired setting will vary.
Topside Control Pad:
Your hot tub is equipped with an electronic topside control pad. The
topside control pad wil allow you to control the speed of the pump,
the light, and the temperature setting, as well as some programming
options. Familiarize yourself with the topside control by viewing the
Operation Guide at the back of this manual.
continued
Escape Premium,
Escape Premium R,
Escape, Sport,
Rendezvous Royal,
Crown II, Impulse,
Encore Premium,
Crown XL
Encore SE, Retreat SE
230v 230v
16A 32A
3 3
5