Safety Devices - Tecomec Super Jolly Manuel D'utilisation Et Entretien

Masquer les pouces Voir aussi pour Super Jolly:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 11
10 Arm blocking handle

9. SAFETY DEVICES

The grinder is equipped with the safety devices illustrated hereafter:
- Shield guards: they protect the operator from parts of the grinding wheel that may
come away during the sharpening process.
These guards must always be fitted in place when the appliance is in use.
Always make sure the guards are efficient and fitted properly. Operator safety could
be compromised if the guards are damaged and/or cracked.
- Switch: the appliance features a safety switch with release coil. In the case of a
sudden power failure, the switch trips automatically and disconnects the appliance
from the mains. The appliance will not start even if the power supply is suddenly
restored. You need to reset the switch to start the appliance again.
10. INTENDED USE
This appliance is an electrical grinder for chains used in chain saws.
- Use the appliance exclusively for the types of chains stated in the technical data
chart.
- Do not use the appliance to cut or grind anything other than the chains envisaged.
- Secure the appliance firmly to the bench or wall.
- The appliance must not be used in corrosive or explosive environments.
- Any other use is to be considered improper.
The manufacturer is not liable for damages following improper or incorrect use of
the appliance.
11. UNPACKING
The grinder is supplied already completely assembled.
12. STANDARD SUPPLY (FIG.2)
1 - Grinder base unit
2 - Instruction manual
3 - Test card
4 - Grinding wheel Ø 145x3.2x22.2
5 - Grinding wheel Ø 145x4.7x22.2
6 - Grinding wheel Ø 145x8x22.2
7 - Operating handle
8 - Sharpening template
13. TESTING THE GRINDING WHEEL
Hold the grinding wheel up by its central hole. Knock the edge of the grinding wheel
(fig.3) gently with a non-metallic object. If it makes a numb non-metallic noise it
means that the wheel could be damaged: do NOT use it!
14. INSTALLATION
ATTENTION
Do not install the appliance at eye level. You are recommended to install it at a height
of no more than 1.2-1.3 meters off the floor.
The appliance can be bench mounted or wall mounted.
14.1 BENCH MOUNTING (FIG.4)
Use 2 M8 screws complete with washers and nuts (material supplied), inserted in the
securing holes F4. Make sure you position the base unit on the bench as illustrated
in the detail.
14.2 WALL MOUNTING (FIG.5)
Use two dowels with relative screws complete with washers (material not supplied),
inserted in the securing holes F6.
14.3 SECURING THE OPERATING HANDLE (FIG.6)
Completely screw the operating handle I7 on the screw V7.
15. CHAIN INFORMATION
The chain must be completely inspected before sharpening it to make sure it is intact.
(fig. 7) Cutter parts:
1 Top part
2 Top cutting angle
3 Side cutting angle
4 Sharpening recess
5 Depth gauge
6 Bit
7 Heel
8 Rivet hole
6
9 - Sharpening template – 3/4''
10 - Dressing brick
11 - 4 mm Allen wrench
12 - 5 mm Allen wrench
13 - M8x80 screw
14 - M8 nut
15 - Washer for M8 screw
16 - Chain stop kit - 3/4"
(fig. 8) Chain parts:
1 Connection link
2 Left cutter
3 Right cutter
4 Driving link (pulling link)
5 Rivet
EN
16. CHAIN IDENTIFICATION
- Before you start to sharpen, you need to know the type of chain and the relative
adjustment angles. These characteristics are written in the owner's manual of the
chain saw on which the chain is fitted or on the chain pack.
- The chain identification code is usually written on the driving link.
- You can also identify the chain using a template or gauge.
- Consult the CHAIN CHART at the end of this manual.
The columns in this chart provide the following information:
÷ 2
A
Chain pitch
B
Driving link width
C
Top sharpening angle (vise rotation)
D
Cutting angle (arm rotation)
E
Down angle (vise inclination)
F
Gauge depth
G
Grinding wheel thickness
H
Grinding wheel code
I
Oregon chain codes
L Windsor chain codes
M SARP chain codes
16.1 INSTRUMENTAL MEASUREMENTS (FIG.9)
a - Measure the gauge depth using the suitable shape.
b - Put the template on this side and measure the chain PITCH.
c - Put the template on this side to measure the cutter length.
d - The driving link width is measured using a suitable instrument (i.e. gauge).
17. GRINDING WHEEL WARNINGS
- Use a grinding wheel suitable for the type of chain to be sharpened; consult the
chain chart at the end of the manual.
- Do not force the grinding wheel on the hub and do not alter the centering hole
diameter. Do not use grinding wheels that do not fit perfectly in place.
- Use exclusively clean and perfect intact hub and flange to fit the grinding wheel.
- Make sure the outside diameters of the hub and flange are identical.
18. FITTING THE GRINDING WHEEL
- Loosen the screw V10 and turn the guard P10 (fig. 10)
- Remove the screw V8 and the flange F8 on the hub (fig.11)
- Choose the grinding wheel based on the type of chain to be sharpened (column H
in chain chart).
- Insert and perfectly center the grinding wheel in the dedicated seat on the hub
(fig.12-13).
- Insert the flange F8 and tighten the screw V8 (fig.12).
Make sure you fit the flange as illustrated in fig.13.
If the grinding wheel is fitted with the flanges too tight, it could break during
use and put the operator at risk. To avoid such risk, tighten screw M6x25
to 7 Nm (if possible, check with dynamometric spanner).
- Close the guard again P10 and tighten the relative screw V10 (fig.14).
18.1 REPLACING THE CHAIN STOP KIT (FOR 3/4" CHAINS)
- The special chain stop kit must be fitted for 3/4" chains only.
- Loosen and unscrew the knob P14 (fig. 14A).
- Remove the chain stop kit K1 (fig. 14B).
- Fit the 3/4" chain stop kit K2 (fig. 14C and 14D).
- Screw up and tighten the knob P15 (fig. 14E).
19. CHECKING THE ASSEMBLY OF THE GRINDING WHEEL
- Stand at the side of the grinding wheel, start the grinder and visually make sure
the grinding wheel does not oscillate sideways or crosswise, consequently causing
abnormal vibrations.
- If this should be the case, stop the appliance immediately and check if the grinding
wheel has been fitted correctly. If necessary, replace the grinding wheel with another
original one.
N Carlton chain codes
O Stihl chain codes
P EM chain codes

Publicité

Table des Matières
loading

Table des Matières