BorMann PRO BPR6050 Mode D'emploi page 3

EN
Safety instructions
CAUTION: Read all instructions and warnings before operating!
SAVE THESE INSTRUCTIONS!
WARNING: To avoid serious injury or death from electrical shock or fire:
1. This fixture MUST ALWAYS BE USED IN ACCORDANCE WITH ALL ELECTRICAL AND SAFETY CODES AND ORDINANCES, including the most recent National
Electric Code (NEC) and with the Occupational Safety and Health Act (OSHA) Volume 1 on General Industry Standards and interpretations.
2. ALWAYS make certain that the power source conforms to the rating on the fixture.
3 DO NOT inspect or service the fixture while charging.
4. Do not charge for longer than 8 hrs. Overcharging will cause overheating and shorten battery life.
5. CAUTION: This fixture is for indoor use. Keep dry. Do not open, drop, short-circuit, incinerate, expose to temperatures higher than 60°C, or charge/use if
damaged.
6. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker
interference or pacemaker failure
7. DO NOT use in potentially dangerous locations, such as in flammable or explosive atmospheres.
8. NEVER operate the light with the clear protective glass broken or removed.
9. NEVER LOOK DIRECTLY INTO LIGHT SOURCE. LED's are extremely bright and can damage eyes with prolonged exposure.
10. KEEP AWAY from heating vents, radiators, or other sources of heat.
11. KEEP OUT OF REACH OF CHILDREN.
Lithium battery safety warnings
LITHIUM BATTERIES STORE A LARGE AMOUNT OF ENERGY AND WILL VENT FIRE OR EXPLODE IF MISTREATED:
1. Keep work light dry.
2. DO NOT DO ANY OF THE FOLLOWING TO BATTERY PACK:
a. Drop
b. Open
c. Short-circuit
d. Puncture
e. Incinerate
f. Expose to temperatures greater than 60°C.
3. Charge work light only according to these instructions
Operating instructions
Battery operation (Pic.1)
1. Press the lower power button to turn on the LED light to the lowest illumination setting of 500 Lumens.
2. Press the lower power button again quickly, to brighten the light to the medium setting of 1,500 Lumens.
3. Press the lower power button a third time quickly, for the full power of 5,000 Lumen LED lights.
4. Press lower power button a final time to turn the light off.
Corded operation
1. Press the lower power button to turn on the LED light to 1,700 lumens.
2. Press lower power button a final time to turn the light off.
To alternate between bright white led and daylight led (Pic.2)
1. Press the lower Power button to your desired illumination level.
2. Press the upper lighting selection button to alternate between the Bright White LED light setting and the Daylight LED setting.
Tripod setup (Pic.3 and 4)
1. Unlatch the top release lever to loosen.
Slide the top portion to desired height and lock into place.
2. Unlatch the bottom release lever to loosen.
Slide the bottom portion to desired height and lock into place.
Tips & Tricks: If the latch is too loose or too tight, we have designed a standard Philips screw allowing you to slightly tighten or loosen the latch locking
tension to your desired setting.
3. To set up legs, simply pull each of the three legs downward, until they automatically lock into place.
Tripod storage (Pic.5 and 6)
1. Unlatch the top release lever to loosen. Slide the top portion downwards fully closing the top portion of the unit.
2. Unlatch the bottom release lever to loosen.
Slide the bottom portion downwards fully closing the bottom portion of the unit.
3. To fold up the legs, simply slide the release lever downwards to unlock the pin that is holding the leg in place. While sliding the release lever down, begin
pulling up on the leg to fold it all the way upwards until snug.
Tips & Tricks: Our legs are designed for stability and you may need to gently pull up or down on the leg to align and disengage the locking pin. If you pull
too hard the pin could be damaged and not align properly.
3
WWW.NIKOLAOUTOOLS.GR