DeWalt DW253 Mode D'emploi page 22
Masquer les pouces
Voir aussi pour DW253:
- Guide d'utilisation (6 pages) ,
- Guide d'utilisation (5 pages)
Publicité
Les langues disponibles
Les langues disponibles
E N G L I S H
Dead spindle drive clutch
This screwdriver is equipped with a dead spindle
feature; the spindle does not turn until the fastener is
pressed into the workpiece. This enables fasteners
to be placed onto the drive accessory of a running
screwdriver.
Electrical safety
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
Your D
WALT tool is double insulated in
E
accordance with EN 50144; therefore no
earth wire is required.
Mains plug replacement
(U.K. & Ireland only)
• Should your mains plug need replacing and you
are competent to do this, proceed as instructed
below. If you are in doubt, contact an authorized
D
WALT repair agent or a qualified electrician.
E
• Disconnect the plug from the supply.
• Cut off the plug and dispose of it safely; a plug
with bared copper conductors is dangerous if
engaged in a live socket outlet.
• Only fit 13 Amperes BS1363A approved plugs
fitted with the correctly rated fuse (1).
• The cable wire colours, or a letter, will be marked
at the connection points of most good quality
plugs. Attach the wires to their respective points
in the plug (see below). Brown is for Live (L) (2)
and Blue is for Neutral (N) (4).
• Before replacing the top cover of the mains plug
ensure that the cable restraint (3) is holding the
outer sheath of the cable firmly and that the two
leads are correctly fixed at the terminal screws.
Never use a light socket.
Never connect the live (L) or neutral (N)
wires to the earth pin marked E or
en - 4
All manuals and user guides at all-guides.com
For 115 V units with a power rating exceeding 1500 W,
we recommend to fit a plug to BS4343 standard.
Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor
size is 1.5 mm
unwind the cable completely.
Also refer to the table below.
Conductor size (mm
0.75
1.00
1.50
2.50
4.00
Voltage
115
230
Assembly and adjustment
Fitting and removing 1/4" hex. drive accessories
Your D
drive system. The drive accessory is retained in the
holder by a ball and a spring which engages in a
groove in the accessory shank.
DW263K/DW274K/DW274KN (fig. B)
• Remove the collar (4) by pulling it forward.
• Select the required accessory (both models) and
.
2
. When using a cable reel, always
2
)
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5
Amperes
Cable rating (Amperes)
0 - 2.0
6
2.1 - 3.4
6
3.5 - 5.0
6
5.1 - 7.0
10
7.1 - 12.0
15
12.1 - 20.0
20
0 - 2.0
6
2.1 - 3.4
6
3.5 - 5.0
6
5.1 - 7.0
10
7.1 - 12.0
15
12.1 - 20.0
20
Prior to assembly and adjustment always
unplug the tool.
WALT Screwdriver has a 1/4" hexagonal
E
matching depth locator (5) when using a
nutsetter (DW263).
15
25
30
45
60
6
6
6
6
10
6
6
6
15
15
6
10
15
20
20
10
15
20
20
25
15
20
25
25
-
20
25
-
-
-
6
6
6
6
6
6
6
6
6
6
6
6
6
10
15
10
10
10
15
15
15
15
15
20
20
20
20
20
25
-
17
Publicité
