Publicité
Les langues disponibles
Les langues disponibles
Alphanumeric keypad for audio-video modules,
buttons with white LED backlighting and audi-
ble feedback, 1 input configurable as external
button for CA door opener or PA door open,
1 N/O relay output, to be completed with front
cover
1. Description
The keypad module provides entry control after keying in a per-
sonal code for Pixel series entrance panels.
2. Features
• The module must be installed in conjunction to an audio or au-
dio/video module (except the basic audio module 41000).
display
• If the speech unit has an
can also be used to make calls to the indoor units, entering the
desired number directly. Without coordinated display the keypad
only works as an access control device.
• The device has:
1) A pair of terminals for an AC input (configurable via Save-
Prog)
2) A pair of terminals for a N/O input (C – NO)
• Power supply from Audio Video or Audio module via harness.
• Current draw: 90 mA (from Audio Video or Audio module).
• Operating temperature: -25 °C / +55°C.
• Protection class: IP54
• IK08-rated for protection against impact (Pixel)
3. Entry control mode (CA)
The device enables activating a programmed command (e.g., lock
opening, relay.. ) by entering a preconfigured code.
3.1. Operation
The keypad has 2 function keys referred to here as:
and
(Key).
Press the
(Key) button to go into "Code Entry" mode.
display
If there is no
module, pressing button C takes you out of
"Code Entry" mode.
Press button
(Key) to confirm and validate the entered code.
In brief:
a. Pressing the
button (Key), (enters code entry mode)
b. Pressing the digit buttons (entering the personal code)
c. Pressing the
button (Key), (confirms the code entered)
d. Feedback for valid code and actuation or invalid code feed-
back.
If the display is installed, pressing
the most recently entered digit; pressing and holding
for two seconds deletes all the digits entered previously; if
(Cancel) is held down for a further two seconds you exit "Code
Entry" mode.
6
module art. 41018, the keypad
(Cancel)
(Cancel) lets you remove
(Cancel)
You exit "Code Entry" mode also if you delete all previously en-
tered digits and then press
If the display is installed, it gives feedback on the validity of the
code entered.
If the above-mentioned buttons are not pressed for more than 5
seconds, the system exits code entry mode.
3.2. Configuration
The codes can be managed and defined by the installer.
The codes have a variable length, and a maximum of 8 digits.
A maximum of 2000 codes can be used.
The codes are programmed by accessing the AV module. Connect
the PC to the USB and follow the SaveProg operating instructions.
4. Call mode
display
If the
module 41018 is fitted, the keypad module can be
used to make a call by directly keying in the desired extension
number.
In standby mode enter the number and confirm.
For more details, follow the instructions of art. 41018.
The instruction manual is downloadable from the site www.
vimar.com
INSTALLATION RULES.
Installation should be carried out observing current installation
regulations for electrical systems in the Country where the prod-
ucts are installed.
CONFORMITY.
EMC directive
Standards EN 60065, EN 61000-6-1 and EN 61000-6-3.
INFORMATION FOR USERS UNDER DIRECTIVE
2012/19/UE (WEEE)
In order to avoid damage to the environment and human
health as well as any administrative sanctions, any appli-
ance marked with this symbol must be disposed of separately
from municipal waste, that is it must be reconsigned to the dealer
upon purchase of a new one. Appliances marked with the crossed
out wheelie bin symbol must be collected in accordance with the
instructions issued by the local authorities responsible for waste
disposal.
This product was developed using FreeRTOS
www.freertos.org/
(Cancel) again.
software - http://
TM
EN
Publicité
