golmar CE-ART 7/G2+ Guide Rapide page 4

CE-ART 7/G2+ GUARD UNIT
SAFETY PRECAUTIONS
Always disconnect the power supply
- before installing or making modifications to the device
.
- The fitting and handling of these devices must be carried out by authorised personnel.
.
- The wiring must run at least 40 cm. away from any other wiring.
- Do not overtighten the screws on the connector.
- Install the guard unit in a dry protected location free from the risk of dripping or splashing water
- Do not place in humid, dusty or smoky locations, or near sources of heat.
- Before connecting the device to the mains, check the connections between the door panel, power
supply, distributors monitors , and guard unit.
- Always follow the instructions contained in this manual.
( ) CHARACTERISTICS
*
- Hands-free monitor.
- 7" colour screen.
- Touch screen for access and selection of menu function.
- Guard unit with simple installation (non-polarised 2 wires bus)
- User menu.
- Installer menu.
- Image and communication settings menu.
- Output auxiliary call repeater (max. 50mA/12V).
- "HZ" input for calls from apartment front door.
- Hidden Push buttons for Start/Stop Commnunication & Door Opening.
- Notification leds.
- Configuration switches: Set Dip 1 to ON, Dip 2 - 7 to OFF and end of line.
( ) SYSTEM OPERATION
*
- To make a call to guard unit , the visitor must press the
audible sound indicates that the call is being made and LED
enabled, a 'Call is in progress' message appears indicating that a call is being made. At this
moment, the guard unit receive the call. If another
correct call button to guard unit and the first call will be cancelled.
- Upon receiving the call, the image will appear on the screen of the master
if it exists) without the visitor knowing and icon
the image from slave guard units 2 or 3, press the screen for the image to appear. If the call is not
answered within 45 seconds, LED will turn off and the system will become free.
- To establish communication, press off-the-hook icon
guard unit . Door panel LED will turn off and the led
- Connection will last for 90 seconds or until on-the-hook icon
up the handset only if communication has been established by lifting the
When communication ends, LED will turn off and the system will become free. If vocal synthesis
is enabled, a 'Communication is finished' message will indicate that the call is over.
- To open door or of the door panel , press the corresponding icon
1 2
or communication processes: one press will activate the lock release for seconds and LED will
also turn on for sec 3 onds . If vocal synthesis is enabled, a 'Door
on the door panel.
- Detailed operation and configuration of the
INSTALLATION OF THE GUARD UNIT
( )
*
( )
* For more information, see "TCE-ART 7/G2+
https://doc.golmar.es/search/manual/50124361
.
corresponding call button to guard unit
will turn on. If vocal synthesis is
call button is press ed by mistake, press the
guard unit (and slave 1,
displayed on the screen will blink green. To view
on the screen or (lift the handset) of any
will turn on .
is pressed on the screen or (hang
handset ) on guard unit
on the screen during the call
3
is open' message will be indicated
guard unit , see "TCE-ART 7 /G2+ " user manual
user manual (cód. 50124361)"
2
CE-ART 7/G2+ GUARD UNIT
( ) DESCRIPTION
*
.
A
.
B
C
D
E
K
L
M
K
( ) Settings as building guard unit:
*
The guard unit(s) to be configured as a build guard unit (up to 4 guard units) in the building, must be
configured with
address 1
monitors, telephones and door panels connected. Then enter the special code '
(programmable by the installer), the guard unit/s with address 1 will be now a building guard unit/s with
; an
address 129 and displaying the symbol
panel will auto-configure the
unit compatible with sound module EL632/G2+ SE V08 + 6587.2 & later, EL642/G2+ V06 & later.
Compatibility of monitors with guard unit, see manual "TCE-ART 7/G2+" page 2.
Dip1 to Dip7:
Set with address 1, Dip 1 to ON
Address 1
ON
1 2 3 4 5 6 7 8
Not : e If there are more than 1 guard unit, to define the guard unit as slave 1, slave 2 or slave 3, configure the
corresponding special code: "0550" Master (factory default), "0551" Slave 1, "0552" Slave 2 & "0553"
Slave 3 programmable by the installer
.
( )
Operation as building guard unit:
*
-The master and slave guard unit(s) receive the call from the access door panel (by pressing button P1 on
the sound module).
-The master and slave guard unit(s) can be autoswitch-on with the access door panel.
-The master & slaves guard unit(s) receive calls from the apartments (by pressing the button below
icon on the main menu of the apartment monitor).
. -The master and slave guard unit(s) can be used to call the apartments (intercom menu, resident list menu
& lost call menu).
-It allows internal intercommunication between the guard units.
-The master and slave guard unit(s) allow to capture the calls of the apartments made from the selected
door panel(s), (programmable by the installer).
( )
* For more information, see
https://doc.golmar.es/search/manual/50124361
EN
A.
Handset.
F
B. Notification icons:
Power on indicator.
Do not disturb.
Auxiliary relay activated.
Door opening.
G
New image/video.
C. Hidden start/stop communication button.
H
For the visually impaired, by default deactivated
(see "TCE-ART 7/G2+" manual, code 50124361).
I
D. Raised dots for the visually impaired
E. Cable slot.
J
F.
Speaker (hands-free communication mode).
G. Touch screen.
H Hidden door opening button.
For the visually impaired, by default deactivated
N
(see "TCE-ART 7/G2+" manual, code 50124361).
I. MicroSD card slot (not included).
Type: MicroSD Class 10 from 4Gb to 128 Gb.
A
J. Microphone (hands-free communication mode).
ON
1 2 3 4 5 6 7 8
K. Wall mounting connector fixing (x4)
SA BUS
GND BUS M
L. Configuration switches.
HZ 24V
HZ GND
M.
Installation terminals.
N. Speaker
O. Microphone (communication with handset).
O
E
and as , , or slave 3, the installation must have all
master slave 1 slave 2
at the top left of the main menu screen.
on the sound module with the
button P1
Dip8: This activates the end-of-line resistance in the ON position. Activate it on
& Dip 2-7 to OFF.
Dip 8 to ON Dip 8 to OFF
ON ON
1 2 3 4 5 6 7 8 1 2 3 4 5 6
).
"TCE-ART 7/G2+ user manual (cód. 50124361)"
3
.
.
(communication with handset).
' in a master monitor
5001
Note: The access door
call address 129 Important: Guard .
guard unit where the bus cable
ends. Deactivate it only in
interm ed iate guard units .
7 8
EN