Publicité
Les langues disponibles
Les langues disponibles
Always wear SAFETY GLASSES
when installing hitch
Conical washer
teeth side
Access
against hitch
hole
Fasteners
typical
both sides
Bumper
beam
Authorized Drawbar Kit:
3593 (Sold Separately)
Drawbar must be used
in the RISE position only.
①
Note: Apply blue thread locker to all bolts.
1.
Remove fascia:
a)
Using Philip screwdriver, remove (2) screws from wheel well liner both sides of vehicle, see Figure 2.
b)
Open trunk to access taillight. Remove taillight trim panel. Using 10mm socket, remove (1) bolt from fascia both sides.
c)
Using flat head screwdriver, remove (5) plastic rivets from fascia and underbody panel.
d)
Using 10 mm socket, remove (2) screws from underbody panel.
e)
Gently remove fascia and set aside in safe place.
2.
Remove bumper: Using 12 mm socket, remove (4) M8 factory bolts from bumper plate each side. Return factory bolts to vehicle owner. Gently remove bumper beam and set aside.
3.
Install hitch:
a)
Push the thin metal piece under the bumper plate inward and make it flush with end panel each side, see Figure 3. Align bumper beam with hitch and attach to end panel with
supplied M8 bolts ①, see Figure 1.
b)
Tighten all M8 fasteners with torque wrench to 20 Ft.-Lb. (27 N*M)
c)
Using 1/2" drill bit, locate hole in bracket on bottom of frame. Drill hole through frame. Feed the carriage bolt ② and spacer ③ through the access hole using the pull wires ⑥.
Remove pull wires and loosely install conical washer ④ and hex nut ⑤ to hitch.
d)
Tighten all 7/16'' fasteners with torque wrench to 50 Ft.-Lb. (68 N*M).
4.
Trim fascia: Trim fascia in area shown in Figure 4.
5.
Trim underbody panel: Trim underbody panel in area shown in Figure 5.
6.
Reinstall fascia, underbody panel, and fasteners removed in previous steps.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged
should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for
connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
© 2023 Horizon Global™ Corp. - Printed in Mexico
Installation Instructions
PART NUMBERS: 25007, 78254, CQT25007
1.00"
⑥
Kink pullwire to keep spacer
Figure 4
independent of bolt
②
End
③
Panel
④
⑤
Figure 1
①
②
8.75"
③
1.625"
7.125"
④
℄
⑤
⑥
Figure 2
Figure 3
Proper torque is needed to keep the hitch secure to the vehicle when towing.
Sheet 3 of 18
25007NP
Fastener Kit: 25007F
Bolt
Qty. (8)
M8 x 1.25 x 35mm CL 9.8
Carriage bolt
Qty. (2)
7/16"-14 x 1.75, GR5
Spacer
Qty. (2)
1/4" x 7/8" x 3"
Conical washer
Qty. (2)
7/16"
Hex nut
Qty. (2)
7/16" -14
Pull wire
Qty. (2)
7/16"
Remove
this area
Figure 5
03-06-23
Rev. A
Publicité
