Publicité
Les langues disponibles
Les langues disponibles
DMP-100T
Order number 17.3520
ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS
Audio Player Insertion Module
GB
with FM Tuner
Please read these operating instructions carefully
prior to operation and keep them for later reference.
1 Applications
This compact audio player module with FM receiver
is designed for installation into an existing unit or into
a separate housing. It is supplied with 12 V DC volt-
age.
The audio player is able to replay audio files in
MP3 format from:
– USB flash drives
– USB hard disks with separate power supply
– SD/SDHC/ MMC memory cards
Note: Due to the large number of storage device manu-
facturers and device drivers, it cannot be guaranteed that
all storage media are compatible with the DMP-100T.
2 Important Notes
The module corresponds to all relevant directives of
the EU and is therefore marked with
G
The module is suitable for indoor use only. Protect
it against dripping water and splash water, high air
humidity and heat (admissible ambient tempera-
ture range: 0 – 40 °C).
G
For cleaning only use a dry, soft cloth; never use
water or chemicals.
G
No guarantee claims for the module and no liabil-
ity for any resulting personal damage or material
damage will be accepted if the module is used for
other purposes than originally intended, if it is not
correctly connected or operated, or if it is not
repaired in an expert way.
If the module is to be put out of operation
definitively, take it to a local recycling plant
for a disposal which is not harmful to the
environment.
3 Installation and Connection
1) If the unit into which the module is to be installed
is supplied with mains voltage, disconnect the
unit from the 230 V mains.
2) To install the module, a cutout of 106 mm ×
19 mm is required. The installation depth is
55 mm. Push the module into the cutout and fas-
ten it via its front panel using four screws.
3) Electrical connection is made via the two pin con-
nectors CN1 (2 poles) and CN2 (5 poles). The pin
configuration can be found on the lower side of
the PCB:
CN 1 connection for antenna supplied
FM-ANT
antenna signal
FM-GND
ground
CN 2 signal output and power supply
+12V
12 V operating voltage, 100 mA
GND
ground
L-CH
output left channel
S-GND
ground
R-CH
output right channel
®
All manuals and user guides at all-guides.com
CN2
PCB with connectors
The module is supplied with a 38 cm connection
cable with 5-pole plugs and an FM wire antenna.
As an alternative, use the adapter cable DMP-
12CC available as an accessory. The adapter
cable is fitted with two RCA inline jacks and a low-
voltage inline jack (5.5 mm / 2.1 mm, positive pole
= centre contact).
4 Operation
4.1 Remote control
1) To insert the batteries (2 × 1.5 V, size AAA), re -
move the battery compartment cover on the rear
.
of the remote control. Insert the batteries as indi-
cated in the compartment, and then close the
compartment with the cover.
If the remote control is not to be used for a
longer period of time, remove the batteries to pre-
vent damage due to battery leakage.
2) When you press a button on the remote control,
always point the remote control at the module.
Make sure that there are no obstacles between
the remote control and the module.
3) If the operating range of the remote control
decreases, the batteries are discharged and
must be replaced.
Never put discharged batteries in the
household waste; always take them to a
special waste disposal, e. g. collection
container at your retailer.
4.2 Audio player
Connect a USB flash drive or a hard disk with sepa-
rate power supply to the USB port
memory card into the slot SD/ MMC (notched corner
pointing to the left and facing the unit). To remove the
card, push the card into the slot until it disengages.
To switch on the audio player, press the
button
on the module or the button MODE on the
remote control repeatedly until
appears on the display. When the audio player is
switched on, the first title will start automatically. All
the other operating options can be found in the fol-
lowing table.
4.3 FM tuner
To switch on the tuner, press the button
module or the button MODE on the remote control
repeatedly until the two LEDs
the same time. The tuner will be automatically
selected when no memory card is inserted and no
USB storage device is connected. All the other oper-
ating options can be found in the following table.
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright
©
by MONACOR INTERNATIONAL. All rights reserved.
Button
remote control
CN1
on the unit
5807P
MODE
MODE
0 ... 9
+10
VOL+
VOL−
RAND
RP1
REPEAT
and / or insert a
RP1
REPEAT
or
briefly
0 ... 9
5 Specifications
Audio player
on the
Frequency range: . . . . . 20 – 20 000 Hz
THD: . . . . . . . . . . . . . . . < 0.2 %
and
light up at
Channel separation: . . . > 60 dB
S / N ratio: . . . . . . . . . . . . 75 dB (A weighted)
Tuner
Received frequency: . . 87.5 – 108 MHz
Tuning increment: . . . . . 50 kHz
General information
Output level: . . . . . . . . . 500 mV
Power supply: . . . . . . . . 12 V
Dimensions, weight: . . . 120 × 22 × 58 mm, 48 g
Subject to technical modification.
Function
Switching on / off, operating mode
to switch on, to switch between USB
port, memory card and tuner;
to switch off: keep button pressed for
3 seconds
to switch on and off
to switch between USB port,
memory card and tuner
Audio player
to start the replay and to switch
between replay and pause
direct title selection
to skip 10 titles
previous / next title:
Press button briefly.
to increase / decrease the volume:
Keep button pressed.
previous / next title: Press button briefly.
fast forward / reverse:
Keep button pressed (sound muted
during the process).
to increase / decrease the volume:
Press button briefly (repeatedly).
replay in random order
– when activated, brief indication
REPEAT 1 / ALL will disappear
– when deactivated, REPEAT 1 / ALL will
reappear
continuous repeat of the current title
– when activated, indication REPEAT 1
– when deactivated,
indication REPEAT ALL
to stop the replay; the display will indi-
cate the number of titles
Tuner
Storing stations
to scan all stations and automatically
store them one after the other: Keep but-
ton pressed for 2 s until the figures start
to appear on the frequency indication.
station scan:
Keep button pressed until the figures start
to appear on the frequency indication.
fine tuning:
Briefly press button (repeatedly).
to store the stations manually:
1. Select an available station number
(
Calling up stored stations).
2. Set the stations (
Station scan-
ning and Fine tuning).
3. Press the button RP1 or REPEAT.
Calling up stored stations
to go to the next station number:
Press button briefly.
direct selection of the station number
± 2 V, 100 mA
A-1582.99.01.06.2014
,
Publicité
