Publicité
Les langues disponibles
Les langues disponibles
en
ENGLISH
- when using a type B guard for cutting-off
operations with bonded Fcut-off wheels, there is
an increased risk of exposure to emitted sparks
and particles, as well as exposure to wheel
fragments in the event of a wheel burst.
- when using a type A, B, C guard for cutting-off
operations or lateral grinding in concrete or
masonry, there is an increased risk of exposure to
dust and loss of control resulting in kickback.
- when using a type A, B, C guard with a wheel-type
wire brush with a thickness greater than the
maximum permitted thickness, the wires may
catch on the guard leading to breaking of the
wires.
Always use the matching guard for the accessory.
See chapter 11.
When working in dusty conditions, ensure that
ventilation openings are not blocked. If it becomes
necessary to remove dust, first remove the battery
pack (use non-metallic objects) and avoid
damaging internal components.
Reducing dust exposure:
WARNING - Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
- Lead from lead-based paints,
- crystalline silica from bricks and cement and other
masonry products, and
- arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals,work in a well-
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
This also applies to dust from other materials, such
as some timber types (like oak or beech dust),
metals, asbestos. Other known diseases are e.g.
allergic reactions, respiratory diseases. Do not let
dust enter the body.
Observe the relevant guidelines and national
regulations for your material, staff, application and
place of application (e.g. occupational health and
safety regulations, disposal).
Collect the particles generated at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit. Observe the
regulations of the suction device for using and
connecting the extraction unit.
Reduce dust exposure with the following measures:
- do not direct the escaping particles and the
exhaust air stream towards yourself or nearby
persons or towards dust deposits,
- use an extraction unit and/or an air purifier,
- ensure good ventilation of the workplace and keep
it clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
18
- Vacuum or wash protective clothing. Do not blow,
beat or brush protective gear.
4.7
Safety instructions for battery packs:
Protect battery packs from water and
moisture!
Do not expose battery packs to fire!
Do not use faulty or deformed battery packs!
Do not open battery packs!
Do not touch or short circuit battery pack contacts!
A slightly acidic, flammable fluid may leak
from defective Li-Ion battery packs!
If battery fluid leaks out and comes into
contact with your skin, rinse immediately
with plenty of water. If battery fluid leaks out
and comes into contact with your eyes, wash them
with clean water and seek medical attention
immediately!
Remove the battery pack from the machine before
making any adjustments, changing tools,
maintaining or cleaning.
Make sure that the tool is switched off before fitting
the battery pack.
Hold the machine when removing and inserting the
battery pack so that the on/off switch cannot be
unintentionally pressed.
If the machine is defective, remove the battery pack
from the machine.
Transport of Li-Ion battery packs:
The shipping of Li-Ion battery packs is subject to
laws related to the carriage of hazardous goods (UN
3480 and UN 3481). Inform yourself of the currently
valid specifications when shipping Li-Ion battery
packs. If necessary, consult your freight forwarder.
Certified packaging is available from Metabo.
Only send the battery pack if the housing is intact
and no fluid is leaking. Remove the battery pack
from the machine for sending. Prevent the contacts
from short-circuiting (e.g. by protecting them with
adhesive tape).
5. Overview
See page 2.
1 Quick clamping nut*
2 Support flange
3 Spindle
4 Autobalancer support flange *
5 Spindle locking button
6 Sliding on/off switch *
7 Handle
8 Fixture bores for tethering (for fall protection)
9 Battery pack release button
10 Battery pack*
11 Switch-on lock*
12 Trigger switch *
13 Dust filter*
14 Electronic signal indicator
15 Adjustment wheel*
Publicité
