Mesko MS 4409 Mode D'emploi page 4

15. The device has to be turned off after every use.
16. In order to provide additional protection, it is recommended to install residue current
device (RCD) in the power circuit, with residual current rating not more than 30 mA. Contact
professional electrician in this matter.
17. Never use the appliance without water! It can cause damage.
18. Never direct a steam or hot water jet toward the body.
19. Never use carbonated water!
20. Never leave the appliance at a temperature below 0 °C as it can cause damage.
21. Before filling the water tank with water, always disconnect the appliance from the mains.
22. Before cleaning, always disconnect the espresso machine from the power supply and
wait until all hot parts have cooled. The appliance should be cleaned with a mild detergent
(without abrasives). Never use a solvent for cleaning, as this can damage the paint.
23. To decalcify the appliance, use espresso machine liquid decalcifier.
24. Never touch the filter holder or the milk frothing nozzle while the appliance is in
operation, as this may cause burns.
DESCRIPTION
5 - Steam Knob
9 - ON/ OFF Switch
12 - Filter Holder Handle
16 - Water Outlet
19 - Ground Coffee Filter
BEFORE FIRST USE
After unpacking the appliance, make sure that all the buttons are off and the Steam Knob (5) is switched to the right. Before use, wipe the
appliance (please see "Cleaning and Maintenance"). Remove the Water Tank (4) and fill it up to MAX. It is recommended to use filtered
water. This prevents lime build-up and improves the taste of the prepared coffee. Do not use carbonated water. After filling the Tank (4)
with water, put it in its place. Remove the Steam Nozzle (17). Then install the Filter Holder (20) by placing it below the Water Outlet (16)
and turning it to the right. Place a cup under the installed Filter. Connect the power cord and press the ON/OFF Switch (9). The ON/ OFF
Indicating Lamp (6) will light up. Press the Coffee/ Hot Water Button (10) immediately and wait until water starts to flow out of the filter.
This means that the hydraulic system of the appliance has been filled with water.
NOTE: If have not used your machine for a few days, it is recommended that you pass at least one cup of water through the hydraulic
system.
HEATING THE ESPRESSO MACHINE
It is important to heat the appliance so that the brewed coffee would have the right temperature. Make sure that the Steam Knob (5) is
closed and there is water in the tank (4). Place the jug under the Steam Nozzle (17). Insert the Filter (19) into the Filter Holder handle (20)
and place it under the Water Outlet (16). If you want the cups to be heated, place them on the Cup Warmer (1). Turn on the machine (9).
Wait until the Ready Lamp (7) has lit up. Place the cups on the Tray (13) and press the Coffee/ Hot Water Button (10). Wait until two cups
of water flow out. Turn the Steam Knob (5) to the left and wait until a small amount of water flows into the cup. Close the Steam Knob (5)
and switch all buttons off.
PREPARING ESPRESSO
The machine is used for preparing espresso. All other beverages (e.g. café latte, latte macchiato are cappuccino) are espresso-based.
Measure the appropriate amount of coffee and place it in the filter (19). To prepare espresso, use one coffee measuring spoon (18). Make
sure that the coffee has been ground properly. Then place the Filter with the coffee inside in the Filter Holder (20). Place the Filter Holder
in the machine, turning it approximately 45 degrees to the right. Fill the Water Tank (4) with cold water. Connect the appliance to a mains
socket. NOTE: Remember that the device requires grounding. Press the ON/ OFF Switch (9) and wait until the ready lamp (7) has lit up.
Press the Coffee Button (10). The brewed coffee will start to flow down through the Coffee Outlet (21). To stop brewing, press the Coffee
Button again (10). To remove the Filter Holder (20), turn it to the left. To facilitate Filter Holder removal, turn the Knob (5) counter-
clockwise to release the pressure.
NOTE: Never remove the Filter Holder (20) during brewing, that is, when the Coffee Button is on (10).
After use, press the ON/ OFF Switch (9) and disconnect the appliance from the power supply.
PREPARING CAPPUCCINO
To prepare cappuccino, you need already brewed espresso and frothed milk warmed up using steam in a separate jug (preferably made
of metal or stainless steel).
Prepare espresso (please see "Preparation"). Pour cold milk into a cooled metal jar. Make sure that the Tank (4) is filled with water. Press
the Steam Button (11). Wait until the Ready Lamp (7) glows indicating that the boiler has reached correct temperature. Place a container
of your choice under the Nozzle (17) and turn the Knob (5) to the left.
some water will come out of the Nozzle and then a strong jet of steam will start to flow out. Turn the Knob (5) clockwise and place the
3 - Water Tank Lid
6 - ON/ OFF Indicating Lamp
10 - Coffee/ Hot Water Button
13 - Drip Water Tray
17 - Milk Frothing Nozzle
20 - Filter Holder
4 - Water Tank
7 - Ready Lamp
11 - Steam Button
14, 15 - Base
18 - Coffee Measuring Spoon
21 - Coffee Outlet
Never use the Knob (5) while the Lamp ( ) is off.
4
7 At the beginning,