Black & Decker GL701 Traduction Des Instructions D'origine page 7

♦ Insert the mains plug into a mains outlet.
Warning! The extension cable must be suitable
for outdoor use.
Residual risks.
Additional residual risks may arise when using
the tool which may not be included in the
enclosed safety warnings. These risks can arise
from misuse, prolonged use etc. Even with the
application of the relevant safety regulations and
the implementation of safety devices, certain
residual risks can not be avoided. These include:
♦ Injuries caused by touching any rotating/
moving parts.
♦ Injuries caused when changing any parts,
blades or accessories.
♦ Injuries caused by prolonged use of a tool.
When using any tool for prolonged periods
ensure you take regular breaks.
♦ Impairment of hearing.
♦ Health hazards caused by breathing dust
developed when using your tool (example:-
working with wood, especially oak, beech
and MDF.)
Use
Warning! Let the tool work at its own pace. Do
not overload.
Setting the appliance to trimming or
edging mode (fi g. B - D)
The appliance can be used in trimming mode
as shown in fi g. B or in edging mode to trim
overhanging grass along lawn edges and fl ower
beds as shown in fi g. C.
Trimming mode (fi g. B & D)
For trimming, the trimmer head should be in the
position shown in fi g. B. If it is not:
♦ Depress the adjustment button (6).
♦ Rotate the tube (7), while releasing the button.
♦ When the head is in position, the button will
lock into place.
Note: The tube will only rotate in one direction.
Edging mode (fi g. C & D)
For edging, the trimmer head should be in the
position shown in fi g. C. If it is not:
♦ Depress the adjustment button (6).
♦ Rotate the tube (7), while releasing the button.
♦ When the head is in position, the button will
lock into place.
Note: The tube will only rotate in one direction.
All manuals and user guides at all-guides.com
Adjusting the height of the appliance
(fi g. D)
This appliance has a telescopic mechanism,
allowing you to set it to a comfortable height.
There are three height settings.
To adjust the height setting, proceed as follows:
♦
♦
♦
Switching on and off
♦
♦
Warning! Never attempt to lock the trigger lever
in the on position.
Hints for optimum use
General
♦
Trimming
♦
♦
♦
♦
♦
Edging
Optimum cutting results are achieved on edges
deeper than 50 mm.
♦
♦
♦
Fitting a new spool of cutting line
(fi g. E & G)
Replacement spools of cutting line are available
from your Black & Decker dealer (cat. no. A6495).
♦
♦
♦
ENGLISH
Depress the adjustment button (6).
Gently pull the tube (7) out of the motor
housing (16) to the desired height, while
releasing the button.
When the tube is in position, the button will
lock into place.
To switch the appliance on, squeeze the trigger
lever (1).
To switch the appliance off, release the trigger
lever.
In order to achieve optimum cutting results,
only cut dry grass.
Hold the appliance as shown in fi g. B.
Gently swing the trimmer from side to side.
When cutting long grass, work in stages from
the top. Take small cuts.
Keep the appliance away from hard objects
and delicate plants.
If the appliance starts running slowly, reduce
the load.
Do not use the appliance to create edges.
To create edges, use an edging spade.
Guide the appliance as shown in fi g. C.
To make a closer cut, slightly tilt the appliance.
Keep the tabs (17) depressed and remove the
spool cover (18) from the housing (10).
Remove the empty spool (19) from the spool
housing.
Remove any dirt and grass from the spool
cover and housing.
7