Tommee Tippee goprep Manuel D'instructions page 3

HOW TO USE
1. Clean and disinfect the surface you are going to use. It is important that you wash your hands.
2. Fill the kettle with fresh tap water (do not use water that has been boiled before). Boil the water.
3. Take care when handling freshly boiled water.
Using the hot flask and Using the cooling flask
cooling flask
4a. Add the boiled water to
4a. Fill the hot flask with
the cooling flask, using
boiling water, and take
the graduation marks on
out of the home with
the inside of the flask.
you.
4b. Measure out the formula
as per manufacturer
instructions and store
in the milk powder
dispenser until you are
ready to use.
4c. When you are ready to
feed, attach the digital
lid to the hot flask,
ensuring it is assembled
correctly, and tilt the
flask upside down for a
minimum of 5 seconds to
ensure the water is still
hot enough and safe to
make a feed. The star on
the digital lid should turn
red.
4d. You can now pour the
water from the hot flask
into the cooling flask
using the graduation
marks on the inside of
the flask for correct
measurements.
5. Add the correct amount of formula powder, as per manufacturers guidelines.
6. Screw the digital lid onto the cooling flask, ensuring it is assembled correctly, and shake well to mix
the powder with the hot water, ensuring its fully dissolved. Shaking the cooling flask starts the cooling
process.
7. The time it takes for the feed to cool depends on the feed size, refer to the table below. To check
if a feed is ready to dispense into a baby bottle, tilt the cooling flask upside down for a minimum of
5 seconds so the milk touches the digital lid. The lid will show a blue star when the feed is ready.
Don't dispense the feed before 2 minutes
8. Decant your feed into a clean, sterile bottle, and follow bottle feeding instructions.
9. Always check the temperature before feeding your baby. Once a feed is made, use straight away.
Hot flask
Cooling flask
DIGITAL LID
The integrated thermometer in the digital lid will activate the digital
screen when it contacts water or milk. The same lid can be used to
take the temperature of milk or water when used on either the cooling
flask or the hot flask (if using on the hot flask remember to remove
the pouring insert). It will tell you when a feed is ready for baby, but
also when water is still hot enough to start making a feed. Activate the
digital screen by tapping the screen.
When testing the temperature of milk
(on the cooling flask)
Blue Star Amber Star Red Star
Feed is too hot, Feed is too hot,
Feed is ready
please wait please wait
Under most circumstances the digital lid will not show a red star when attached to the
cooling flask. This is because the cooling flask will start cooling the feed immediately and
brings the feed temperature below the range that would show a red star. That is why we
recommend you test the temperature of your water before making a feed by placing the
digital lid on the hot flask to ensure the water is safe to make a feed.
COOLING TIMES
Cooling times should be used as a guide only. Always check food temperatures before
feeding. Always follow formula powder manufacturer's instructions for making a feed.
Feed size 90ml 120ml 150ml
(ml / fl oz) 3 fl oz 4 fl oz 5 fl oz
Time to cool
2m 2m
(minutes)
COOLING FLASK RESET TIMES
Sterilisation / Cold water Electric steam
Cleaning method Sterilisation
Reset Time
3h
(hours)
The cooling flask works by absorbing heat from hot liquids. After being exposed to heat, it
will require a minimum of 3 hours before being ready to use again.
When testing the temperature of water
to make up a feed (on the hot flask)
Blue Star Amber Star
Water is too cold Water is too cold
to make a feed to make a feed
180ml 210ml 240ml
6 fl oz 7 fl oz 8 fl oz
3m 4m 5m 5m
UV Dishwasher
Sterilisation Sterilisation
4h 3h 3h
Red Star
Water is hot enough to make
a feed, add your formula now