Vimar LINEA 30475 Serie Documentation page 2

LINEA EIKON ARKÉ
30475.x 20485 19485
Passive infrared presence detector - 2 modules.
Sends an ON message when activated by the IR sensor tripping (persons or ani-
mals moving through the sensor's range of action) and by the light sensor.
CHARACTERISTICS.
• Rated supply voltage: BUS 29 V
• Input: 10 mA
• Capacity: 10 m
• Terminals: TP BUS
CONFIGURATION.
FOR THE OPERATIONS OF CONFIGURATION, SEE THE INSTRUCTIONS
MANUAL FOR THE By-me Plus SYSTEM.
• Functional blocks: 1; each functional block can belong to at most 4 groups.
• Selecting the functional block (configuration): during group creation, when requi-
red by the app, pressing the device button:
- press the configuration button, the red LED will light up;
- with the red LED on, the app will configure the functional block; at the end of this
operation the red LED will go out.
PARAMETERS.
• tamper threshold: 0-15
• on delay 0-62 s
• brightness threshold 0-100 %
• PIR pulse threshold (number): 1-10
• pulse breadth 0.125-8,000 s
• duration of actuation: 10-250 s
• The brightness threshold permits adjusting the device trip mode, determined by
two conditions occurring at the same time:
- ambient brightness less than the setting;
- motion detection by IR sensor.
• With the brightness threshold set to 100%, the device only trips in total darkness,
as the threshold is decreased the device will trip at greater brightness levels.
• The duration of actuation is used to repeat, the system is disarmed, the com-
mand message to the actuator associated. In practice, after commanding the
actuator, the detector checks whether there are additional movements for a
period of time equal to the duration of implementation and, if this has occurred,
at the end of this time interval will send a new message to the actuator indepen-
dently the brightness setting.
• LED status:
- green LED blinking with each motion detection and device tripping (with burglar
alarm system turned off or absent)
- red LED blinking for tamper alarm
- red LED on steady in configuration.
• Default parameters:
- Tamper threshold: 0
- On delay: 0 s
- Brightness threshold 100 %
- PIR pulse threshold (number): 3
- Pulse breadth: 0.375 s
INSTALLATION RULES.
Installation should be carried out by qualified personnel in compliance with the
current regulations regarding the installation of electrical equipment in the country
where the products are installed.
CONFORMITY.
EMC directive. RoHS directive. Standards EN IEC 60669-2-1, EN 50491, EN IEC
63044, EN IEC 63000.
REACH (EU) Regulation no. 1907/2006 – Art.33. The product may contain traces
of lead.
30475-485 01 2203
IDEA PLANA
16935 14485
FRONT VIEW.
30475.x
A + B
A: led
B: configuration button
BACK VIEW.
DETECTION RANGE DIAGRAM.
1,2
D
0
m 0 1,5
A = 3 rays +6
B = 6 rays +0
C = 5 rays -20
D = 3 rays -30
A
C
B
A
C
C
B B
C
B
8 m
D
D D
1,5 m
112
RAEE - Informazione agli utilizzatori
If the crossed-out bin symbol appears on the equipment or packaging, this means the product must not
be included with other general waste at the end of its working life. The user must take the worn product
to a sorted waste center, or return it to the retailer when purchasing a new one. Products for disposal can
be consigned free of charge (without any new purchase obligation) to retailers with a sales area of at least
400 m , if they measure less than 25 cm. An efficient sorted waste collection for the environmentally friendly
2
disposal of the used device, or its subsequent recycling, helps avoid the potential negative effects on the
environment and people's health, and encourages the re-use and/or recycling of the construction materials.
20485-19485-16935-14485
A B
RIVELATORE PIR
BUS
+ –
terminals
TP bus
C
8 10
Portata nominale
A
C
B
Detection range
• Detection solid angle:
- 112 horizontally
- 36 min. vertically
- 17 zones in 4 levels
• Range: 10 m max (8 m typically)
Viale Vicenza, 14
36063 Marostica VI - Italy
www.vimar.com