IVT HPC-1400B Mode D'emploi page 13

(HPC-1400B; HPC-1800B)
To fit the detergent spray attachment, proceed as
follows:
1. Make sure that the handgun (11) is locked in the
OFF position.
2. Fill the detergent tank (8) with a suitable
biodegradeable detergent. [F7]
3. Fit the detergent sprayer (7) to the tank (8) by
inserting the detergent delivery tube into the tank and
screwing the nozzle on to the head of the tank.
4. Connect the detergent sprayer to the handgun (11).
[F8]
5. Release the lock-off button (12) and point the
nozzle at the area to be sprayed.
6. Squeeze the the switch lever (16).
7. Proceed with the wash.
(HPC-2000B; HPC-2500B)
To spraying detergent, proceed as follows:
1. Make sure that the handgun (11) is locked in the
OFF position.
2. Pull the cap of detergent tank (8).
3. Pull up the regulating sleeve of the lance with spray
regulation (10). [F9]
4. Put a suitable detergent into the tank and push
down the cap. [F10]
5. Release the lock-off button (12) and point the
nozzle at the area to be sprayed.
6. Squeeze the switch lever (16).
7. Proceed with the wash.
CAUTION!
been designed for use with the
cleaning agents recommended by
the manufacturer. The use of other
cleaning agents or chemicals may
adversely affect safety and durability
of the appliance.
The use of the folding transport handle (19) [F11]
(HPC-1800B)
Before moving the device it must be switched OFF
and protected against unintentional start. To move the
device upstairs or over obstacles, lift it by the handle.
Pull out the folding transport handle (19) when you want
to move the machine.
Push in the folding transport handle (19) after use it.
The use of the winding high pressure hose device
(15) [F12]
(HPC-2500B)
The winding high pressure hose device (15) can be
moved using the handle provided.
To increase the length of the hose rotate the handle
clockwise.
All manuals and user guides at all-guides.com
This appliance has
To shorten the length of the hose rotate the handle
counterclockwise.
Using the washer
We recommended that washing procedure should be
performed in two stages:
1. Dirt dissolution: introduce the washing fluid into
a fan shaped jet stream and wait for a moment until the
fluid begins working.
2. Dirt removal: wash the dirt off with a point jet
stream.
∙ While cleaning, make sure that the washer is
positioned on an even base.
∙
You should not move outside the work area limited
by the length of the high pressure hose, as you may
upset the washer's balance.
∙ While washing vertical surface, apply the washing
fluid upward.
MAINTENANCE AND STORAGE
Before any work on the device itself,
pull the mains plug.
∙ Always keep the tool and the ventilation slots (if
present) cleaned. Regular cleaning and maintenance of
the appliance will ensure efficiency and prolong the life
of your tool.
∙ If the tool should fail despite the rigorous
manufacturing and testing procedures, the repair should
be carried out by an authorized IVT customer service.
∙ Keep all nuts, bolts, and screws tight, to be sure the
tool is in safe working condition.
∙ Replace worn or damaged parts for safety.
∙
Use only original spare parts. Parts not produced
by manufacturer may cause poor fit and possible injury.
∙ Store the tool in a dry room out of reach of kids and
away from any flammable material.
∙ Never wet the device or spray water on it!
Cleaning instruction
Keep the body of the washer clean and free from debris.
The high pressure hose (14), the handgun (11) and the
lance with spray regulation (10) should also be kept
clean. Regular cleaning of the nozzle is important to
the efficient operation of the washer. The nozzle must
be cleaned at regular intervals using the nozzle cleaner
(17) provided. [F13]
Storage
∙ Disconnect the high pressure hose (14), the
handgun (11) and the lance with spray regulation (10),
13
Instruction manual
EN