IVT HPC-1400B Mode D'emploi page 11

Specific safety rules
∙
Use a strain relief device with extension cords to
relieve tension.
∙ If the power or extension cord couplings are
replaced, their water-resistance and mechanics integrity
must be preserved.
∙
Always protect electrical parts of the device against
water jet.
∙ Always comply with the requirements of local water
company. The machine may only be connected to the
main drinking water supply if a backflow preventer valve
is installed in the supply hose of the appliance.
∙ All hose connection threads must be watertight.
∙ Damaged high-pressure hoses must not be used due
to blowout danger. Replace damaged hoses immediately.
Use only hoses and couplers provided by the manufacturer.
∙
Do not run the washer without water. This will
cause damage to it.
∙
Before using the device check it and its accessories
for proper condition and operating safety. A faulty device
must not be used.
∙
This appliance has been designed for use in
combination with cleaning agents recommended by
the manufacturer. Under no circumstances use solvent-
containing liquids or undiluted acids/solvents! Such
liquids include petrol, paint thinners and fuel oil. In
aerosol these liquids are highly inflammable, explosive
and toxic. In addition, acetone and undiluted acids or
solvents can cause damage to device components.
∙ Should the device be operated in dangerous areas
(e.g., at filling stations), proper safety prescriptions are
to be observed. Any use of the device at the explosive
hazard facilities is strictly forbidden.
∙
Position the device on solid surface.
∙ All conductive parts in the work area must be splash
protected in all directions.
∙ Do not lock the pistol grip lever when operating in
the ON position.
∙
Always wear protective clothing and safety glasses
as loose particles and other debris may be propelled at
high speed by the water jet.
∙ Under no circumstances should high-pressure
water stream be directed towards people, animals, the
device itself or its electric parts.
∙ To prevent high-pressure stream from damaging
tires and valve stems, a distance of at least 30 cm must
be maintained during cleaning. The first sign of tire
damage is its color alteration. Damaged tires and valve
stems pose death risk.
∙ Do not clean asbestos-filled materials or other
hazardous materials with water stream.
∙ The device must never be left unattended while the
motor is running.
∙ The water outflow produces recoil force against the
nozzle pistol grip. Therefore, hold the pistol grip and the
nozzle pipe firmly.
All manuals and user guides at all-guides.com
UNPACKING
When unpacking, check to make sure that all
components are included. Refer to the drawings on this
manual. If any parts are missing or broken, please call
an IVT assistance center.
ASSEMBLY INSTRUCTIONS
To prepare the high pressure washer for use proceed
as follows:
1.
pressure hose (14) to the high pressure water outlet (4).
Tighten the connector by hand only. [F1]
2.
(16) in the OFF position. [F2]
3.
water supply (3) (the water supply hose is not provided
in the pack). [F3]
4.
to the handgun (11), use a spanner (not supplied) to
tighten the screw. [F4]
5.
handgun (11). [F5]
6.
is fully open.
7.
8.
of winding device (15) until appropriate length.
The pressure washer is now ready for use.
INITIAL OPERATION
Always use the correct supply voltage: the power supply
voltage must match the information quoted on the tool
identification plate.
SWITCHING ON / OFF
Switching On
11
Instruction manual
Fasten the connector at the end of the high
Push the lock-off button (12) to lock the switch lever
Connect the water supply hose to the connection for
WARNING! The temperature of the
incoming water supply must not
exceed 50°C.
Fasten the end of the high pressure hose (14)
Connect the lance with spray regulation (10) to the
Turn the water supply on, making sure that the tap
Plug the mains power cable into electricity.
(HPC-2500B) Pull the high pressure hose (14) out
WARNING! Before using the pressure
washer make sure that there are no
other people or domestic animals in
the work area.
EN