Storage; Load Chain; Maintenance; Emergency Procedure In Case Of An Incident - Tractel bravo Instructions D'emploi Et D'entretien

4.4. Important additional instructions
1� When taking the bravo™ hoist out of service ensure
that there is no load applied and that the load chain
is slack enough to enable the bottom hook to be
removed from the load.
2� The selector lever must not be left in the neutral
position "0" when a load is suspended or the hoist
is tensioned. Make sure that the selector lever is in
the desired position and is not located between two
positions�
3� Do not attempt to operate the load wheel during any
operation or when a load is suspended on the hoist.
4� It is not recommended to operate the lever handle
at excessive speed as this will lead to an uneven
movement of the load. It is recommended to operate
the lever handle in a steady movement to prevent
any unnecessary jerking of the load.
GB

5. STORAGE

It is recommended that the hoist be stored hanging so
that the load chain does not become tangled. Store the
hoist in a dry and weather-proof area. Before storage
clean the load chain with a brush and lubricate with
machine oil.

6. LOAD CHAIN

The good condition of the load chain is a guarantee of
safety and at the same time the good operation of the
hoist. It is therefore necessary to constantly be aware
of the condition of the load chain and to clean and
lubricate with machine oil at regular intervals.
The load chain must be examined daily by a competent
person when the hoist is being used (see technical data
sheet T2208).
Do not expose the load chain to excessive temperatures,
abrasive materials or chemicals. Protect the chain
against all possible damage such as from welding arcs.

7. MAINTENANCE

Periodically, or at least once every year, and in
accordance with the safety regulations applicable in the
country of use, the hoist must be inspected and tested
with load by qualified maintenance personnel.
Periodically, and especially after an intensive use,
lubricate the mechanical parts. Never let brake discs
receive some lubricant. They have to be kept clean and
dry�
Regularly check the condition of the hooks. If the
deformation between the hook opening indicators
is greater than 2 mm, (Fig. 6, distance "M" given in
table of § 2 Technical specifications), the unit must be
considered as damaged and removed from service�
If any damage is observed, return the bravo™ hoist to a
Tractel -approved repair workshop.
®
14
8. EMERGENCY PROCEDURE IN
CASE OF AN INCIDENT
In the event of a blocked chain or any other malfunction
of the unit, immediately stop the maneuver without
attempting any further actions and call in the necessary
qualified personnel to remove the load and intervene
on the hoist.
Immediately set up a safety perimeter around the hoist
and directly under the load to prevent access by any
unauthorized persons. Return the hoist to a Tractel
approved repair agent�

9. MARKINGS

9.1. Standard marking
A nameplate is riveted to each bravo™ hoist (fig. 7),
containing the following information:
• item 1: hoist designation,
• item 2: Working Load Limit (WLL*) in t,
• item 3: dimensions of load chain,
• item 4: CE marking,
• item 5: manufacturing date YYMM (YY: last two
figures of the year of manufacture MM: month
of manufacture),
• item 6: symbol indicating that you must read this
manual before using the hoist,
• item 7: manufacturer's address and contact data:
Tractel SAS France
RD 619 Saint-Hilaire-sous-Romilly
BP38 – F-10102 FRANCE
• item 8: Serial No,
• item 9: direction of movement of lifting hook.
• item 10 : The bravo™ hoist uses the "Double click"
system, see Section 1�
9
bravo
1
3
10
0 0 0 0.5 t
2
N°
8
RD619 Saint-Hilaire-sous-Romilly
Fig. 7
9
™
6
5 x 15 5 x 5 x x 15
4
5
5 5 t
7
TRACTEL S.A.S.
BP 38 - F-10102 FRANCE
www.tractel.com
-
®