Publicité
Les langues disponibles
Les langues disponibles
The scale is calibrated before leaving the manufacturer's
facility. Vibrations in shipping may cause the scale to
fall out of calibration. Uline recommends re-verifying
calibration in the field before first use. You must use a
precision calibration weight to properly calibrate the
scale. The calibration weight must be at least 1/3 of
the scale's capacity and cannot exceed the scale's
capacity.
NOTE: Calibration can be done in English
system weight (lb.) or Metric system weight (kg).
CALIBRATION WEIGHT (lb
Model #
1/3 WEIGHT (Minimum)
H-1654
2 lb.
H-1653
2 lb.
H-1649
4 lb.
H-1650
10 lb.
H-1651
20 lb.
CALIBRATION WEIGHT (kg
Model #
1/3 WEIGHT (Minimum)
H-1654
1 kg.
H-1653
1 kg.
H-1649
2 kg.
H-1650
5 kg.
H-1651
10 kg.
SINGLE POINT CALIBRATION (SPAN)
Single point calibration uses two calibration points: zero
and any weight between 1/3 of the scale's capacity
and full weight of the scale capacity. Refer to the
calibration weights charts above.
1. Turn on the scale. In weighing mode, press the
UNIT key
Unit
until the desired weighing unit
lb
kg
appears –
or
.
2. Turn off the scale. Turn on the scale. During the
%
self-test, press the
simultaneously and release.
on the display.
UnLoAd
3. Remove all weight from the platform.
4. Once the stable indicator
press the ZERO key
used will be shown on the display.
PAGE 7 OF 27
All manuals and user guides at all-guides.com
)
.
FULL CAPACITY (Maximum)
6 lb.
6 lb.
12 lb.
30 lb.
60 lb.
)
.
FULL CAPACITY (Maximum)
3 kg.
3 kg.
6 kg.
15 kg.
30 kg.
%
key
and TARE key
UnloAd
will be shown
O
is shown on the display,
. The last calibration weight
Zero
CALIBRATION
%
5. Use the
enter the calibration weight you are using.
6. Press the ZERO key
display.
LoAd
7.
Place the calibration weight on the platform.
8. Once the stable indicator
press the ZERO key
9. Scale will enter a self-test mode. Remove weight
before self-test mode is complete. After completing
the self-test, the scale will enter the weighing mode.
MULTI-POINT CALIBRATION (LINEAR)
Multi-point calibration uses three calibration points: zero,
1/3 and full weight capacity of the scale. Refer to the
calibration weights charts above.
1. Turn on the scale. In weighing mode, press the
UNIT key
lb
kg
or
.
2. Turn off the scale. Turn on the scale. During the
self-test, press the
simultaneously and release.
on the display.
UnLoAd
3. Remove all weight from the platform.
4. Once the stable indicator
press the ZERO key
will be shown on the display.
5. Place the 1/3 calibration weight on the platform.
6. Once the stable indicator
Tare
display, press the ZERO key
calibration weight will be shown on the display.
7.
Place the full capacity calibration weight on the
platform.
8. Once the stable indicator
press the ZERO key
9. Scale will enter a self-test mode. Remove weight
before self-test mode is complete. After completing
the self-test, the scale will enter the weighing mode.
%
Limit
, LIMIT
and TARE
LoAd
.
will be shown on the
Zero
O
is shown on the display,
.
Zero
until the desired weighing unit appears –
Unit
%
key
and LIMIT key
%
UnloAd
O
is shown on the display,
. The 1/3 calibration weight
Zero
O
is shown on the
. The full capacity
Zero
O
is shown on the display,
.
Zero
Tare
keys to
Limit
will be shown
0417 IH-1649
Publicité
