Télécharger Imprimer la page
Eaton FlexiTech Exit Dual CGLine+ Manuel
Eaton FlexiTech Exit Dual CGLine+ Manuel

Eaton FlexiTech Exit Dual CGLine+ Manuel

Publicité

Liens rapides

Manual
All manuals and user guides at all-guides.com
Manuale / Manuel / Betriebsanleitung / Manuál / Navodila / Priručnik / Uputstvo / Használati utasítás / Instrukcja
ZNO2047800 PrC
FlexiTech Exit Dual CGLine+
+ Web-Controller CGLine+
228 mm
x1
x1
1
a
0 V
1
2
c
Drill in the honeycomb zones or in the flexible material.
11/2019
34 mm
x1
x1
x1
b
1
120 mm
228 mm
2,5 mm
Break through a cable
entry using a screwdriver.
B
C
!
Drilling zones to avoid
+ 45°C
+ 5°C
LiFePO
Before use
24h
Ref. 40071352379
F - 1600g
x2
Ø 5 mm
If cable entry on the
right
Min. 5cm
Rigid or flexible wire
2,5 < Ø < 13,5 mm
2
A

Publicité

loading

Sommaire des Matières pour Eaton FlexiTech Exit Dual CGLine+

  • Page 1 Manual All manuals and user guides at all-guides.com Manuale / Manuel / Betriebsanleitung / Manuál / Navodila / Priručnik / Uputstvo / Használati utasítás / Instrukcja ZNO2047800 PrC 11/2019 FlexiTech Exit Dual CGLine+ + 45°C + 5°C + Web-Controller CGLine+ LiFePO 120 mm Before use...
  • Page 2 TEST Lamp Green & yellow 10 wks 10 wks 10 wks 2 s. Yellow 10 wks 10 wks 10 wks 10 wks 10 wks 10 wks Battery Yellow 0,5 s. Constant Blinking FLEXITECH EXIT DUAL CGLINE+ ZNO2047800 PrC 11/2019 www.eaton.com...
  • Page 3 Disconnect the battery, wait for 10 seconds, and reconnect it if you decide to change configuration (steps 2-3). See CGLine+ Web-Controller (and variants) user manuals. PICTOGRAM CONFIGURATION CLICK 2 CLICK 1 CEILING MOUNTING Back See steps 4 c-d. FLEXITECH EXIT DUAL CGLINE+ ZNO2047800 PrC 11/2019 www.eaton.com...
  • Page 4 WEEE: Contact your local dealer EMEA Headquarters Route de la Longeraie 7 Eaton.com/recycling ZNO2047800 PrC- 11/2019 1110 Morges, Switzerland Eaton.eu Eaton is a registered trademark. © 2019 Eaton All trademarks are property All Rights Reserved of their respective owners. 100 %...
  • Page 5 All manuals and user guides at all-guides.com - Cabling of connectors with a - Break through a cable entry using - Drill in the honey- screwdriver. - See user manuals a screwdriver. comb zones or in the Before - Cabling of connectors by hand. - Non-maintained - Rigid or f lexible wire flexible material.
  • Page 6 All manuals and user guides at all-guides.com - Disconnect the battery, wait for - Even/ Odd - Autotest 10 seconds, and reconnect it if you - LED Description - Installation - Duration Test Day D - Charge / Lamp / decide to change configuration date - Green / Yellow...
  • Page 7 All manuals and user guides at all-guides.com - Magnet Test - Replaceable - Functional Test - Not replaceable - Back - Duration Test Pictogram Ceiling mounting - Battery pack, Order code configuration - See steps 4c-d - Reset luminaire - If the battery duration is insufficient, replace - DIM level the battery.