Table des Matières
Publicité
Preface
The WOLF tradition comprises the principles of helping you to cre-
ate your dream lawn as well as making appreciable improvements
to established lawns. It is the responsibility of our lawn experts to
develop the products which make the possibility of creating a dream
lawn available to everyone, independent of climate and soil conditions.
This goal is achieved using our lawn seed and special lawn fertiliser.
However, seed and fertiliser can only be distributed efficiently using a
scattering car. This scattering car has been completely redeveloped
ssembly
Calibration (basic setting) of the scattering rail (fig. M12/
M13/M14)
• Set the adjustment screw on the dosing device to no. 5 (M12).
The number 5 must be fully identifiable.
• Fix the lever to the handle using a quick fastener (M13).
• Then tip the scattering car forwards. Loosen the lock nut M14
(1) and turn the calibration screw M14 (2) until the front edge
Operation
Fill with scattering material
• This should not be done on the lawn as scattering material may
be lost through accidental spillage or the lawn may be damaged
through extreme over-fertilisation.
Set scattering quantity (fig. B1)
• For scattering settings, please observe the instructions on the
label or accompanying leaflet. Please also observe the instruc-
tions on the packaging.
• Set the desired scattering settings (number) via the adjustment
screw on the dosing device (illus.).
Scattering pattern (fig. B2)
good scattering pattern can be achieved by scattering in
Maintenance
Maintenance and care
•
fter each utilisation
- Empty scattering car
- Thoroughly clean container
- Clean scattering apertures using a stiff brush.
Guarantee terms
Please carefully retain the guarantee card completed by the seller,
or the proof of purchase.
The company WOLF-Garten provides a guarantee for 24months from the
date of purchase. This guarantee is in accordance with the relevant state of
technology and the utilisation purpose / area of application. The consumer's
statutory rights are not affected by the following guarantee guidelines.
Pre-conditions for the 24-month guarantee entitlement:
- Deployment of the device solely for private use.
The guarantee is reduced to 12 months in the commercial sector
or leasing business.
- Proper handling and observance of all information given in the
operating manual, which forms part of our guarantee terms.
- Observance of the prescribed maintenance intervals.
- No unauthorised alteration of the design.
6
We would like to wish you many hours of recreation on your dream lawn.
according to the requirements of professional garden care.
The result: the first efficient scattering car for the precise and meas-
ured distribution of seed and fertiliser.
The special scattering mechanism ensures that the various scattering
materials are distributed over the ground precisely and in accurately
measured amounts. The scatter-stop-lever fitted to the handle of the
unit is particularly practicable. This can be used for accurate determi-
nation of the scattering areas.
of the dispersal bar M14 (3) and the marking are aligned (see
arrow in figure M14), or until there is 6 mm clearance between
the lower edge and the marking (M14 Q). Then hold the
calibration screw (2) and tighten the lock nut (1).
• The quick fastener must then be released (pull the small strap
according to M14, D). Your scattering car is now ready for use.
The quick fastener is reusable M13).
the longitudinal direction of the lawn. It must be ensured that
scattering overlaps, so that no areas are left uncovered. It is
recommended that several strips are scattered in the lateral
direction at the ends of the lawn.
We recommend that you:
• push the scattering car before lifting the scattering lever;
• release the scattering lever before you stop walking.
Note (fig. B3/M9/M10/M11)
If you only mow in straight lines, we recommend the installation of the
coupler. The scattering shaft is then driven by both wheels.
Wash the scattering device with of water if extremely dirty (sticky
deposits). The scattering device must be thoroughly dry before
the next utilisation.
Recalibrate (basic setting)
The basic setting can change over time. To recalibrate, proceed
as described under assembly, M12/M13/M14.
- Installation of original WOLF replacement parts / accessories.
- Presentation of the completed guarantee card and/or proof of purchase.
This guarantee does not extend to normal wear-and-tear on blades,
blade mounting components or friction disks, V-belts/toothed belts,
running wheels/tyres, air filters, spark plugs and spark plug connectors.
ny guarantee claim shall be immediately void in the event of
unauthorised repairs.
Faults and defects which can be traced to material or manufacturing
faults will be rectified exclusively by our contracted workshops (the
seller has the right to remedy a defect) in your vicinity, or by the
manufacturer if the latter is closer.
provision of a guarantee are ruled out. There is no entitlement to a
replacement. ny transport damage should be reported not to us but
to the shipper in question since, otherwise, any compensation claims
vis-à-vis the shipper would be voided.
ny claims going beyond the
Publicité
Table des Matières
