Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Signify Classified - Internal
Read and understand these instructions before installing luminaire (fixture).
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding. Allow fixture to cool
before handling. Retain these instructions for maintenance reference.
INSTRUCTIONS FOR INSTALLING AND OPERATING LWWH20 AND LWWH40 SERIES TRACK HEAD.
FOR USE WITH 120V MODEL "L" SERIES MANUFACTURED BY HALO
-
Compatible with ceiling mounted track.
-
Compatible with certain types of dimmers. See specification sheets for compatible dimmers.
-
Compatible with 81LV4 Louver and 81VZ4 Visor.
-
CAUTION: HOT SURFACE. Keep away from curtains and any other combustible materials.
-
CAUTION: Turn power off and allow fixture to cool before handling.
-
CAUTION: No consumer serviceable parts. Contact factory if service is required.
-
CAUTION: For use in dry locations only.
INSTRUCTIONS FOR ATTACHING LUMINAIRE TO TRACK.
1. Turn off power to TRACK.
A. SINGLE CIRCUIT TRACK FIG. 1
1. Orient ADAPTER with TRACK as shown in FIG 4.
2. Push ADAPTER into TRACK.
3. Rotate ADAPTER (2) CONTACTS in direction of GROOVE until ADAPTER
SLEEVE snaps into track. FIG. 5
4. To remove fixture: Pull down ADAPTER SLEEVE and rotate adapter until
removed from track.
B. TWO-CIRCUIT TRACK FIG. 2
1. Raise contact for upper circuit using a flat blade screwdriver until contact
stops against plastic. Position MOVABLE contact to desired position. Leave
contact in lower position for lower circuit of two circuit track (FIG. 3).
2. Follow instructions above for installing into track.
Fig. 5
1/28/2019
page
1
www.lightolier.com
Halo is a registered trademark of Cooper Technologies Company.
TRACK
ADAPTER
SLEEVE
Track Lighting
LyteSpan BoldFlood
LWWH Series
NEUTRAL
CIRCUIT
UPPER
CIRCUIT
LOWER
CIRCUIT
TRACK
GROOVE
ADAPTER
Fig. 4
TRACK
Fig. 1
GROOVE
HALO TRACK
SINGLE CIRCUIT
TRACK
GROOVE
Fig. 2
HALO TRACK
TWO CIRCUIT
MOVABLE
CONTACT
ADAPTER
Fig. 3
Publicité
Manuels Connexes pour SIGNIFY LIGHTOLIER LWWH Serie
Sommaire des Matières pour SIGNIFY LIGHTOLIER LWWH Serie
- Page 1 Signify Classified - Internal Track Lighting LyteSpan BoldFlood LWWH Series Read and understand these instructions before installing luminaire (fixture). This luminaire is intended for installation in accordance with the National Electrical Code and local regulations. To assure full compliance with local codes and regulations, check with your local electrical inspector before installation.
- Page 2 Signify Classified - Internal IS:LWWH20/LWWH40 LyteSpan BoldFlood INSTRUCTIONS FOR INSTALLING LOUVER 81LV4 : 1. Turn off power to TRACK. 2. First insert BOTTOM SPRINGS on the LOUVER into the BOTTOM GROOVE in the luminaire (Fig. 6 & 7) 3. While pushing down TOP SPRING TABS, rotate LOUVER toward the TOP GROOVE in the luminaire until it hits the FRONT STEP on the luminaire.
- Page 3 Signify Classified - Internal IS:LWWH20/LWWH40 LyteSpan BoldFlood Bien lire et comprendre ces directives avant d’installer le luminaire (projecteur) Ce luminaire doit être installé en respectant les réglementations du Code électrique national et des codes locaux. Afin de bien respecter les codes et réglementations locaux, veuillez vérifier auprès de votre inspecteur électrique local avant d’installer. Pour prévenir les chocs électriques, veuillez couper l’alimentation au panneau avant de débuter.
- Page 4 Signify Classified - Internal IS:LWWH20/LWWH40 LyteSpan BoldFlood DIRECTIVES POUR INSTALLER LE PARALUME 81LV4 : 1. Couper l’alimentation du RAIL. 2. Installer d’abord les RESSORTS INFÉRIEURS sur le PARALUME dans la RAINURE INFÉRIEURE du luminaire (Fig. 6 et 7) 3. Tout en appuyant vers le bas sur la LANGUETTE DU RESSORT SUPÉRIEUR, faire pivoter le PARALUME vers la RAINURE SUPÉRIEURE du luminaire jusqu’à...