Black & Decker GL301 Mode D'emploi page 8

ENGLISH
Fitting a new spool of cutting line (fig. H - J)
Spool with single cutting line (fig. H)
Replacement spools of cutting line are available from your
Black & Decker dealer (cat. no. A6481).
Keep the tabs (16) depressed and remove the spool cover
(17) from the housing (12).
Remove the empty spool (18) from the spool housing.
Remove any dirt and grass from the spool cover and
housing.
Take the new spool and unwind approximately 9 cm of
cutting line.
Feed the cutting line through the eyelet (19).
Push the spool onto the drive shaft (20) and rotate it
slightly until it is seated. Make sure that the cutting line
is not trapped under the spool and that 9 cm of cutting
line protrudes from the housing.
Align the tabs on the spool cover with the holes in the
housing.
Push the cover onto the housing until it snaps securely
into place.
Warning! If the cutting line protrudes beyond the trimming
blade (10), cut it off so that they just reach the blade.
Spool with twin cutting line (fig. I & J)
Replacement spools of cutting line are available from your
Black & Decker dealer (cat. no. A6441). Complete cassettes
containing a spool of cutting line are also available (cat. no. A6488).
Keep the tabs (21) depressed and remove the spool cover
(22) from the housing (12).
Remove the empty spool (23) from the spool cover.
Remove any dirt and grass from the spool cover and
housing.
Take the new spool and push it onto the boss in the spool
cover. Rotate the spool slightly until it is seated.
Unclip the end of one of the cutting lines and feed the line
into one of the eyelets (24). The line should protrude
approximately 9 cm from the spool cover.
Unclip the end of the other cutting line and feed the line
into the other eyelet. The line should protrude
approximately 9 cm from the spool cover.
Align the tabs (21) on the spool cover with the cut-outs
(25) in the housing.
Push the cover onto the housing until it snaps securely
into place.
Warning! If the cutting lines protrude beyond the trimming
blade (10), cut them off so that they just reach the blade.
8
All manuals and user guides at all-guides.com
Winding a new cutting line onto an empty spool (fig. K - O)
You may wind new cutting line onto an empty spool.
Spool with single cutting line (fig. K & L)
Replacement packs of cutting line are available from your
Black & Decker dealer (cat. no. A6170 (25 m) & A6171 (40 m)).
Warning! Only use the appropriate type of Black & Decker
cutting line.
Spool with twin cutting line (fig. M - O)
Replacement packs of cutting line are available from your
Black & Decker dealer (cat. no. A6440).
Warning! Only use the appropriate type of Black & Decker
cutting line. Ensure that cutting line is present in both sections
of the spool.
Remove the empty spool from the tool as described
above.
Remove any remaining cutting line from the spool.
Feed 2 cm of cutting line into one of the holes (26) in the
spool as shown.
Bend the cutting line and anchor it in the L-shaped slot (27).
Wind the cutting line onto the spool in the direction of the
arrow (28). Make sure to wind the line on neatly and in
layers. Do not criss-cross.
When the wound cutting line reaches the recesses (29),
cut the line. Let the line protrude approximately 9 cm from
the spool and hold a finger on the line to keep it in place.
Proceed as described above to fit the spool on the tool.
Remove the empty spool from the tool as described
above.
Remove any remaining cutting line from the spool.
First wind new line onto the uppermost part of the spool:
– Feed 2 cm of cutting line into one of the slots (30) in the
upper section of the spool as shown.
– Wind the cutting line onto the spool in the direction of
the arrow (31). Make sure to wind the line on neatly
and in layers. Do not criss-cross.
– When the wound cutting line reaches the recesses (32),
cut the line.
– Temporarily park the line in the slots (33) on one side of
the spool as shown.
Repeat the above procedure for the second cutting line on
the lower section of the spool. Park the line in the unused
slots (33).
Proceed as described above to fit the spool on the tool.
Do not forget to release the cutting line from the parking
slots (33).