Publicité
Les langues disponibles
Les langues disponibles
▶ Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
▶ Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may
exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
▶ Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature
above 130° C (265 °F) may cause explosion.
▶ Follow all charging instructions and do not charge the battery pack or tool outside the temperature
range specified in the instructions. Charging improperly or at temperatures outside the specified range
may damage the battery and increase the risk of fire.
Service
▶ Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
▶ Never service damaged battery packs. Service of battery packs should only be performed by the
manufacturer or authorized service providers.
2.2
Additional safety instructions for pressing tools
Safety when working in the vicinity of electrical installations
Invariably, before work commences a risk assessment has to be carried out, and the necessary protective
measures have to be implemented.
All personnel involved in work in the vicinity of electrical installations must have received instruction
concerning the applicable safety requirements, safety regulations and company operating procedures
Working procedures are divided into three different procedures: dead working, live working, working in the
vicinity of live parts. All these procedures are based on the use of protective measures against electric
shock and/or the effects of short-circuits and arcing. For further details refer to EN 50110 and any national
requirements and practices. It shall be verified that all methods and tools chosen are suitable for the
installation to be worked on.
▶ For all work on electrical installations, observe the valid international, national and local laws and
regulations, such as EN 50110.
Personal safety
▶ Comply with the country-specific standards and safety instructions for operation of crimping / pressing
tools and all work on, with or in proximity to electrically live equipment and lines.
▶ Persons who work in the vicinity of live lines must receive regular instruction and training.
▶ Use the crimping / pressing tool only when it is in technically faultless condition.
▶ Never tamper with or modify the crimping / pressing tool in any way.
▶ If you notice oil escaping, cease working with the tool and consult Hilti Service. Immediately remove the
leaked oil.
▶ Check that the locking pin is pushed in all the way and securely engaged.
▶ Throughout the crimping / pressing operation, take great care to keep your hands and fingers well clear
of the crimping / pressing head.
▶ Switch the crimping / pressing tool on only after bringing it to the working position.
▶ Be extra-careful when working on lines that are under mechanical tension.
▶ Always hold the crimping / pressing tool firmly with both hands on the grips provided for the purpose.
▶ Before each use, inspect the black coating on the tool head for indications of damage or aging. If you
find such damage, the red coating is visible and/or the crush-hazard or electric-shock hazard symbol is
no longer legible, do not use the crimping / pressing tool and contact Hilti Service.
▶ Do not secure a belt hook to this power tool.
▶ Risk of injury by falling tools and/or accessories. Before starting work, check that installed accessories
are secure.
▶ Do not look directly into the light source (LEDs) of the power tool and do not aim the beam at other
persons' faces. Risk of dazzling and you could injure the eyes.
▶ Keep the retaining strap and the tether clean and dry.
Electrical safety
▶ Before use of the crimping / pressing tool, all live cables and other equipment carrying electric voltage
within the area in which the user is working are to be switched off. If this is not possible, the corresponding
safety precautions for working in proximity to electrically live cables or equipment applicable in your
country must be implemented and observed.
4
English
2215655
*2215655*
Publicité
