Publicité
Les langues disponibles
Les langues disponibles
All manuals and user guides at all-guides.com
IV. MINIMUM AND MAXIMUM TEMPERATURE RECORDS
The WS-9065U keeps a record of the MINIMUM and MAXIMUM
temperature, and the time and date of their occurrence-for both
the indoor and outdoor modes.
A. VIEWING THE INDOOR TEMPERATURE RECORDS
1. Press the IN button once. "MIN" appears above the indoor
temperature and the LCD will flash, indicating that the minimum
temperature (along with the humidity measured at that time)
and the time and date of occurrence are displayed. The
minimum records will display for 30 seconds before returning
to the normal display mode.
INDOOR
MIN
HUMIDITY
%
RH
2. Press the IN button again (once while "MIN" is still displayed,
twice otherwise). "MAX" appears above the indoor temperature
and the LCD will flash, indicating that the maximum temperature
(along with the humidity measured at that time) and the time
and date of occurrence are displayed.
3. While "MAX" is still displayed press the IN button again to return
to the current data display. Or you can wait 30 seconds, during
either the minimum or the maximum readings, and the unit will
automatically return to current data readings.
B. VIEWING THE OUTDOOR TEMPERATURE RECORDS
1. Press the OUT button once. "MIN" appears above the outdoor
temperature and the LCD will flash, indicating that the minimum
temperature, and the time and date of occurrence are displayed.
The minimum records will display for 30 seconds before
returning to the normal display mode.
2. Press the OUT button again (once while "MIN" is still displayed,
twice otherwise). "MAX" appears above the outdoor
temperature and the LCD will flash, indicating that the maximum
temperature and the time and date of occurrence are displayed.
OUTDOOR
MAX
2
GB
P.14
B. VIEWING AND OPERATING WITH MULTIPLE REMOTE
TEMPERATURE SENSOR UNITS
1. To view the temperature of a different remote temperature
sensor unit, press and release the CH button. A shift from one
"boxed" number to the next should be observed in the
OUTDOOR LCD.
2. To view the Minimum/Maximum temperature: first select which
remote temperature sensor to read data from (indicated by the
"boxed" number), then press the OUT button. Pressing this
button once will display the minimum temperature, and the date
and time the data was recorded. Pressing this button a second
time (while "MIN" is still displayed, otherwise press the button
twice) will display the same data for the maximum recordings.
3. To reset the Minimum/Maximum readings, it is necessary to
select which remote temperature sensor you wish to reset.
Press and hold the OUT button for 5 seconds, the records for
the selected remote temperature sensor unit will be reset.
MOUNTING
Note: Before permanently mounting ensure that the indoor weather
station is able to receive WWVB signals from the desired location.
Also, extreme and sudden changes in temperature will decrease
the accuracy of the indoor weather station, and changes in
elevation will result with inaccurate weather forecasting for the
next 12 to 24 hours. These changes will require a 12 to 24 hour
wait before obtaining reliable data. To achieve a true temperature
reading, avoid mounting where direct sunlight can reach the remote
temperature sensor or indoor weather station. While the remote
temperature sensor is weather proof, avoid submersion in water
or snow. We recommend that you mount the remote temperature
sensor on an outside North-facing wall. The sending range is 80ft-
obstacles such as walls, concrete, and large metal objects can
reduce the range. Place both units in their desired location, and
wait approximately 15 minutes before permanently mounting to
ensure that there is proper reception. The indoor weather station
should display a temperature in the OUTDOOR LCD within 4
minutes of setting up.
I. THE REMOTE TEMPERATURE SENSOR
The remote temperature sensor can be mounted in two ways:
•
with the use of screws, or
•
using the adhesive tape.
A. MOUNTING WITH SCREWS
1) Remove the mounting bracket from the remote temperature
sensor.
GB
P.16
3. While "MAX" is still displayed press the OUT button again to
return to the current data display. Or you can wait 30 seconds,
during either the minimum or the maximum readings, and the
unit will automatically return to current data readings.
C. RESETTING THE MIMIMUM AND MAXIMUM RECORDS
1. All the Indoor records (minimum and maximum) will be reset
after the IN button is pressed and held for 5 seconds.
2. All the Outdoor records (minimum and maximum) will be reset
after the OUT button is pressed and held for 5 seconds.
V. ADDING REMOTE TEMPERATURE SENSORS (OPTIONAL)
The WS-9065U is able to receive signals from 3 different remote
temperature sensors. The remote temperature sensor model(s)
that you choose will come with their own set of instructions-follow
these instructions for a complete guide to setting up. Following
are some brief instructions for the basic set-up of remote
temperature sensor units with the WS-9065U. These extra sensors
can be purchased through the same dealer as this unit, or by
contacting La Crosse Technology directly. A TX6U will monitor
temperature only, a TX3U will monitor temperature and display
the temperature on its LCD, and the TX3UP will monitor the
temperature via a probe for use in pools, spas, etc.
Note: When setting up multiple units it is important to remove the
batteries from all existing units in operation, then to insert batteries
first into all the remote temperature sensor units, and in numeric
sequence. Second install batteries into the indoor weather station.
Transmission problems will arise if this is not done correctly and if
the total time for set-up exceeds 6 minutes.
A. SET-UP OF MULTIPLE UNITS
1. It is necessary to remove the batteries from all units currently
in operation.
2. Remove the battery covers to all remote temperature sensor
units.
3. Place all remote temperature sensor units in a numeric
sequential order.
4. In sequential order, install batteries (follow the same battery
installation procedures seen in section I. A) of the Detailed
Set-Up Guide).
5. Install batteries into the indoor weather station.
6. Follow the Detailed Set-Up Guide for programming and
operating instructions.
2) Place the mounting bracket over the desired location.
3) Through the three screw holes of the bracket, mark the
mounting surface with a pencil.
4) Screw mounting bracket onto the mounting surface. Ensure
that the screws are flush with the bracket.
5) Insert the remote temperature sensor into the bracket.
B. MOUNTING WITH ADHESIVE TAPE
1) With a nonabrasive solution, clean and dry the back of the
mounting bracket and the mounting surface to ensure a secure
hold. The mounting surface should be smooth and flat.
2) Remove the protective strip from one side of the tape.
3) Adhere the tape to the designated area on the back of the
mounting bracket.
4) Remove the protective strip from the other side of the tape.
5) Position the remote temperature sensor in the desired location,
ensuring that the indoor weather station can receive the signal.
II. THE INDOOR WEATHER STATION
The indoor temperature station can be mounted in two ways:
•
with the table stand or
•
on the wall with the use of a wall hanging screw (not included).
A. USING THE TABLE STAND
1) The indoor temperature station comes
with the table stand already mounted.
If you wish to use the table-stand all
that is required is to place the indoor
temperature station in an appropriate
location.
B. WALL MOUNTING
1) Remove the table stand. To do this, pull
down on the stand from the rear and
rotate forward.
2) Fix a screw (not included) into the
desired wall leaving approximately 3/
16 of an inch (5mm) extended from the
wall.
3) Place the indoor temperature station
onto the screw using the hanging hole
on the backside. Gently pull the station
down to lock the screw into place.
GB
P.15
GB
P.17
Publicité
