Start And Programmes - Hotpoint Ariston TCDG 51XB Mode D'emploi

Start and Programmes

The Controls
GB
! Warning, after pressing the START/PAUSE button
the programme cannot be changed. To change a selected
programme, press the START/PAUSE button
flashes Amber to indicate the programme is paused. Select
the new programme and any options required, the light will
then flash green. Press the START/PAUSE button
and the new programme will start.
• Option buttons
These buttons are used to customise the selected
programme to your requirements. A programme must
have been selected, by pressing a programme selection
button, before an option can be selected. Not all options
are available for all programmes. If an option is not
available and you press the button, the buzzer will
beep 3 times. If the option is available the indicator, on the
display unit next to the bottom buttons, lights to show that
the option has been selected.
Delay Timer (Time Delay)
The start of some programmes can be delayed for up to 24
hours. Ensure the water container is emptied before setting
a delayed start.
Pre Care
This option is only available if a delayed start has been
selected. It tumbles the clothes occasionally during the
delayed period to help prevent creases developing.
Post Care
TWhen available and selected, the clothes are occasionally
tumbled after the end of the drying and cool tumble cycles,
to help prevent creases developing should you not be
available to remove the load immediately the programme is
complete.
Note: The Start/Pause light flashes Amber during this
phase.
Heat Level button, Display and Icons
Not all programmes allow you to change the heat level and
some programmes allow all three heat level options:
Low, Medium and High.
When the heat level options are available pressing this
button changes the heat level and the display briefly shows
the selected heat level, along with a display of the selected
level icon:
HIGH HEAT
Sound
Available on all programmes and allows the buzzer to give a
signal at the end of the drying cycle, to remind you that the
clothes are ready to be removed.
Mini Load
Available with programmes: Cotton High Heat 4kg and
Synthetic Medium Heat 1kg.
This option optimises Automatic programme for smaller
loads and improves the Time to End estimation.
30
LOW HEAT
MEDIUM HEAT
• TIME DISPLAY
The display shows either the amount of time delay remaining or
,
an indication of the amount of time left for a drying programme
(see The Display). The display also shows if there is a problem
the light
with your dryer, if this occurs the display will show F followed by
a fault code number (see Troubleshooting).
again
• Empty Water Container
(Messages about emptying can be ignored if you have plumbed
your dryer into a drain as there is no need to empty the water
container). Messages are displayed to reminds you to empty
the water container (see The Display). If the water container fills
during a programme, the heater turns off and the dryer does a
period of Cool Tumble. After this it stops and a message tells
you to
EMPTY THE WATER CONTAINER
container and restart the dryer or the clothes will not dry. After
re-starting the dryer the message will take a few seconds to go
out. To avoid this always empty the water container each time
you use the dryer (see Maintenance).
• Door Opening
Opening the door during a programme will stop the dryer and
have the following effects:
Note: The START/PAUSE
Post Care phase of a programme
• The display shows
• During a delay phase the delay will continue to count down.
The START/PAUSE
the delay programme. The display will change to show current
status.
• The START/PAUSE
the programme. The display will change to show the
current status.
• During the Post Care phase, the programme ends. Pressing
the START/PAUSE
from the beginning.
• Note
If you have a power cut, switch off the power or remove the
plug. When power is restored, press and hold the On/Off
button until the display briefly shows
reactivates. Then press the START/PAUSE
programme will resume.
. You must empty the water
light flashes Amber during the
.
PAUSED
button must be pressed to resume
button must be pressed to resume
button will restart a new programme
and the dryer
POWER ON
button and the