Publicité
Les langues disponibles
Les langues disponibles
To unclip the harness:
1. Hold the tool by the pole with your
left hand.
2. Grip the clip with your right hand and
unclip by pushing the gate outwards
and lifting the harness mount out of
the clip.
OPERATION
To reduce the risk of injury, always
WARNING
wear proper eye protection marked
to comply with ANSI Z87.1.
Always remove battery pack before changing or
removing accessories or attachments.
Do not operate the tool without the correct guard
in place. The guard must be attached properly
during use. Operating the tool without the guard
could cause serious injury.
During operation, use the harness. Keep the
brush cutter on your right side firmly.
Use both hands when operating the tool. Maintain
a firm grip. Using one hand could cause loss of
control and result in serious injury.
Inspect the area before using the tool. Remove
all debris and hard objects such as rocks, glass,
wire, etc. that can ricochet, be thrown, or otherwise
cause injury or damage during operation.
Selecting the Speed
Use the speed control button to select Low
or High speeds. Use low speed for larger
jobs where extended battery life is needed.
Use high speed for dense growth applica-
tions.
Starting/Stopping the Power Head
To reduce the risk of injury, always
WARNING
hold the power head away from the
body keeping clearance between body and the
tool/attachment. Any contact with an attachment
or cutting head can result in cuts, burns and
other serious personal injury.
Always remove the battery pack and keep hands
clear of the trigger and lock-out when carrying
or transporting tool.
1. Grasp the tool firmly by both handles.
2. To start the tool, toggle the lock-off lever and pull
the trigger.
3. To vary the speed, increase or decrease the pres-
sure on the trigger. The further the trigger is pulled,
the greater the speed up to the maximum set by
the speed control button.
4. To stop the tool release the trigger. Make sure the
tool comes to a complete stop before laying the
tool down.
Brush Cutting
1. Grasp the trigger handle with your right hand and
the left handle with your left hand to properly align
yourself behind the handle assembly with the tool
at your right and away from the direction of cut.
2. To start the tool, toggle the lock-off lever with your
thumb and pull the trigger.
3. To vary the speed, increase or decrease the pres-
sure on the trigger. The further the trigger is pulled,
the greater the speed up to the maximum set by
the speed control button.
4. If a blockage occurs, remove the battery before
clearing the blockage from the tool.
1. Grasp the trigger handle with your right hand and
the left handle with your left hand to properly align
yourself behind the handle assembly with the tool
at your right and away from the direction of cut.
2. To start the tool, toggle the lock-off lever with your
thumb and pull the trigger.
3. To vary the speed, increase or decrease the pres-
sure on the trigger. The further the trigger is pulled,
the greater the speed up to the maximum set by
the speed control button.
4. Allow the tool to angle down, keeping at least 12"
between the trimmer head and any body part. Hold
the tool just above the ground and swing the head
side to side.
NOTE: The trimmer will cut best when moved
across the ground in the direction of the arrow
on the guard.
High
Low
5. WARNING! Do not use tool as an edger. Do not
tilt tool to create a right angle to the ground. Keep
trimmer head and line parallel to the ground.
Guard cannot protect against flying debris in this
orientation.
6. To feed out the line, bump it against the ground
gently while running a normal speed.
NOTE: When used near abrasive surfaces or in
dense growth, the cutting line will wear faster and
require "bumping" more often.
7. To stop the tool release the trigger. Make sure
the tool comes to a complete stop before laying
the tool down.
Thick grass, brush, weeds, small diameter trees
and saplings
For string trimmer:
• Allow the ends of the line to do the cutting.
• Contact between the line and solid objects will cause
extra line wear and breakage.
• Do not drag the spool cover along the ground or
bump it too hard. Only bump spool on the ground.
Do not bump against rocks, driveways, etc.
• Make multiple passes in long growth.
• Avoid ornamental trees, shrubs, and plantings.
Avoid contact with siding, fence posts, etc. They
can all be damaged by the tool.
9
String Trimming
12" MINIMUM
Materials to Cut
Cutting Tips
Publicité
