Energy Connoisseur C-R1 Mode D'emploi page 2

O w n e r s M a n u a l
We are proud to welcome you as an owner of ENERGY Speaker Systems' new
Connoisseur Series speakers.
ENERGY Speakers are the result of extensive research into accurate sonic
reproduction and represent the leading edge in speaker design and performance.The
finest components and cabinet materials combined with sophisticated manufacturing
and quality control procedures, ensure many years of exceptional performance and
listening pleasure.
Please take time to read all of the instructions contained in this manual to make
certain your system is properly installed and set up for optimal sound
reproduction.
Be sure to unpack your system carefully. Retain the carton and all packing material
for future use.
POSITIONING YOUR SPEAKERS
Rear Channel Speakers (C-R1)
The rear speakers can vary greatly in position depending on the room layout, and
the furniture placement.The ideal position is either on the side walls, or rear walls.
Side Wall:This position utilizes the rear walls of the room to reflect sound and create
the "surround" effect.
Rear Wall:This is generally used when the side wall position is not available to you,
due to furniture placement or room dimensions.
Both mounting positions have their advantages and disadvantages, the position
offering the best coverage of the entire room should be chosen.
The goal of the surround speakers is to create an "atmosphere" around you.The rear
channel speakers are ideally placed an equal distance from you as compared to the
front speakers. But this is not always possible in a home environment.The C-R1 will
emit sound from both sides of the speaker, and is best placed where it can use the
walls to reflect from.The best mounting position is the Side Wall position, as it makes
use of the rooms' rear walls, and front walls. It will create a lifelike surround effect
and make the room sound larger than it is. In this position, try to mount the speaker
so that it is beside you, as opposed to behind you.The height should be above ear
level, at approximately 2/3 of the height of the wall.
You can also achieve excellent results in the rear position.Try not to place the
speakers directly into a corner. Leave a few feet between the edge of the cabinet
and the side wall so the sound can reflect into the room environment.The rear
position is usually chosen when your room will not accommodate the side wall
position due to unequal walls, a doorway, or a large opening, etc. Please see
Diagrams 1 and 2.
NOTE: For 6.1 channel systems.
The C-R1 is sold individually, so if you wish to add a third rear center speaker, it
can easily be achieved by mounting the speaker between the other two rear
surrounds. It is recommended that the rear center be placed at the same height as
the other two rear surround speakers wherever possible. Please see Diagrams 1
and 2.
CONNECTING YOUR SPEAKERS
You may utilize high quality speaker cables, up to 12 gauge, as well as numerous
types of connector types including spade lugs, banana jacks, or pin type connectors.
The best connector in our opinion is the "Spade lug" as it provides more contact
with the terminal and allows the binding post to be tightened for a secure
connection. Audiophiles and novices alike have preferences as to which connector
type is best, speak with your Authorized ENERGY retailer as to which is the best for
your Audio Video System. Rest assured, plain speaker wire is more than acceptable,
you can always upgrade your wires and/or connectors later on.
2
To Connect your speaker system: Always ensure that the entire A/V system is
powered off before performing any connections. The positive and negative (red and
black) sides of the speaker terminals MUST match the positive and negative (red and
black) terminals of the receiver or amplifier. If they do not match, abnormal sound
and a lack of bass response will result. Make sure you follow the amplifier
manufacturers owners manual to ensure your are connecting the speaker correctly
to the rear channel amplifier output terminals. See Diagram 3.
MOUNTING YOUR SPEAKERS
NOTE:The C-R1 is not difficult to mount to the wall, but careful attention must
be made to mount it securely as the speaker is heavy and damage to the product
and/or injury could result from improper mounting. Please follow the directions
carefully!
1) Select the mounting position best suited for your room.
2) Attach the included mounting template to your wall, and mark the center of the
four large circles. (See Diagram 8) This is where you need to insert the
appropriate mounting hardware to securely fasten a load of 10 lbs. Hardware is
not included with the speaker, as building materials vary greatly in different
countries, but the recommended screw head size is a #8. Screw length is to be
determined by the wall material.
3) If you are mounting directly to drywall, please ensure that you use molly
anchors, as screws into drywall itself will not provide a secure mount. Insert the
anchors, then the screws, leaving 1/4" of the screw exposed. See Diagrams 4
and 5.
NOTE:Try to locate into wall studs wherever possible.
4) Hold the speaker upright, and insert the four screws into the mounting holes.
Let the speaker fall into place, it will slide down
the length of the mounting hole, which is about 1/2". See Diagrams 6 and 7.
RECOMMENDATIONS
Amplifier Requirements:
All ENERGY Connoisseur Series Speakers are designed to operate on a wide range
of receivers and/or amplifiers.The impedance for all models is rated at 8 ohms,
allowing almost any amplifier to function well. Of course, the better the amplifier and
the system components, the better the overall system will sound.
Care of Finishes:
Your ENERGY Connoisseur Series Speaker should be gently wiped clean with a
warm, lint free cloth. Do not use any type of cleaner, or abrasive as they can damage
the finish.
WARRANTY OUTSIDE OF THE UNITED STATES:
Outside of North America, the warranty may be changed to comply with local
regulations. Ask your local ENERGY dealer for details of the LIMITED WARRANTY
applicable in your country.
WARRANTY FOR THE UNITED STATES AND CANADA:
Please see the warranty document on the back cover
"ENERGY", the "ENERGY" logo, are trademarks of Audio Products International Corp.