Fujioh BUF-011 Manuel D'installation

1U03 2183
Model: BUF-011/021
SAFETY INSTRUCTIONS
Before installation and operation, read these instructions carefully
and use this product only in the manner described by the
manufacturer in the operation manual.
The instruction shown below are used to alert you to potential
personal injury and property damage hazards.
There are three hazard classifications based on potentially
dangerous situations.
Obey all safety instructions that show these symbols to avoid
possible injury, death and property damage.
WARNING:
WARNING indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION:
CAUTION indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
CAUTION:
CAUTION used without the safety
alert symbol indicates a potentially
hazardous situation which, if not
avoided, may result in property
damage.
NOTE: The safety instructions are explained with the following
pictographic symbols.
means prohibition. It indicates actions, if any,
that mustn't be done.
means forcible execution. It indicates actions,
if any, that must be done.
WARNING
1. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b) Before servicing or cleaning unit, switch power
off at service panel and lock the service
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.
2. To reduce the risk of fire or electric shock, do not
use this product with any solid-state speed control
device.
3. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Installation work and electrical wiring must be
done by a qualified person(s) in accordance with
all applicable codes and standards, including fire-
rated construction.
1. Preparation
WARNING:
• If the range hood is not installed properly, it could become detached
and fall.
• Ensure that the metal duct does not touch other metal housing
materials, otherwise fire or electric shock could result.
1
According to the conditions where the
Roof cap
6" round duct
range hood is installed, determine
(For vertical
whether it will be discharged vertically
discharge)
or horizontally (6" Round duct). For
vertical or horizontal discharge, run
duct work between the hood location
and the roof cap or wall cap. For best
result in either direction, use a
Wall cap
Soffit
minimum number of transitions and
elbows. Be sure to attach a roof cap or
wall cap to avoid rain/wind entry. 6" round duct
(For horizontal
Range hood
discharge)
2
The range hood unit must be mounted to a liner which has the
following dimensions. Install the liner securely after checking that
the opening size of the liner is the same as the figure below.
Liner Dimensions (Unit: inch) Front
18-11/16"
17-1/2"
Liner
4- 1/4"
Holes for mounting range hood
Center line
Range hood cutout
CAUTION:
The liner shape illustrated in this installation manual is only for
reference.
CAUTION:
• When the liner is installed in the wooden hood, the inside of the
wooden hood placed above the cooking surface must be fully
covered by the metal barrier including bottom edges. Select a
suitable liner and metal barrier according to the size and shape of
the wooden hood and install properly.
• The liner should be installed tightly. If the liner installation is not
correct, the range hood unit may become detached and fall.
3
Run house wiring between service panel and hood location.
4
Prepare the range hood unit.
Tape
Detach
(1) The range hood is supplied with the the tape.
exhaust pipe fixed on its top plate.
Exhaust pipe
(2) Detach the tape stuck on the
exhaust pipe.
(3) Arrange the ends
of 6" round duct
and wiring
2-1/4"
conduit so that
5-7/8"
they can connect
with the top of the
range hood unit.
5-3/16"
(4) Be sure to keep 1-3/16"
Duct
overlapping length of the
exhaust pipe and duct.
1-3/16"
Range
hood
unit
Liner
All manuals and user guides at all-guides.com
Range Hood
INSTALLATION MANUAL
b) Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney)
of fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer's
guidelines and safety standards such as those
published by the National Fire Protection
Association (NFPA), and The American Society
for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code
authorities.
c) When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
d) Ducted fans must always be vented to the
outdoors.
e) This unit is designed for ducted or ductless
installation. When ductless kit part numbers
FDK-021 is installed, this unit is certified ductless.
The end user is responsible to ensure compliance
with all Federal, State and Local Environmental
and Fire codes.
4. TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
5. This unit must be grounded.
6. Check that the hood is correctly installed, since
incorrect installation could result in the range hood
becoming detached and falling off.
7. Connect only to an AC120 Volt power source or
the range hood could result in fire, electric shock,
and damage.
CAUTION
1. For general ventilating use only. Do not use to
exhaust hazardous or explosive material and
vapors.
2. To reduce the risk of fire and to properly exhaust
air, be sure to duct air outside. Do not vent exhaust
air into spaces within walls or ceilings or into attics,
crawl spaces, or garages.
3. Read specification label on this product for further
information and requirements.
4. Use only for the purpose of kitchen ventilation.
5. Do not install this range hood in the bathroom or
in other wet rooms since electrical shock and
damage may result.
6. Fasten the filter and other parts securely. Incorrect
attachment may result in personal injury or
property damage.
7. Keep your hands and other objects away from
the fan while it is in motion. The range hood may
injure you or damage itself.
INSTALLATION
(5) Remove the following parts by following steps.
1. Filter: Loosen 2 knobs and detach the slot filters.
2. Front cover: Remove 4 screws fixing the front cover and
detach it.
Then, turn it over and remove 2 cushions of
foamed polystyrene put on its both ends.
Filter
Front cover
Cushion
WARNING:
• Remove the cushions without fail, otherwise there is a risk of fire.
3. Wire cover: Remove 1 screw and do as illustrated below.
Wire cover
1 Detach 2 tabs. 2 Slant the wire cover. 3 Remove the wire cover
by lifting and rotating it
as illustrated after
removing the screw.
2. Range Hood Mounting
CAUTION:
• Wear working gloves to avoid injury.
1
Hold up the range hood and insert it into the opening of the liner.
When the 4 securing plates on both sides have passed through
the top of the liner, turn them outward to secure the range hood
on the liner temporarily. Make sure the top of the exhaust pipe is
inserted into the bottom of the duct.
Duct
Duct
Securing plate
[each side
two (2) places]
Range hood unit
Liner
Liner
Securing
plate Liner
Securing plate turns
while passing through
the opening of Liner
Range hood unit
2
Align 4 screw holes of the liner and range hood unit, then fix
securely using the supplied screws and nuts.
Note: Fasten all the screws and nuts evenly.
Nut with plate
Nut with plate
[left & right, each
two (2) places]
Range hood unit
Liner
Four screws
Four (4) screws (M5×30)
NAMES OF PARTS
Lamp
(standard MR16-GU10, 35Watt)
Enclosure
(not supplied)
Slot filter
Switch
Front cover
ACCESSORIES
Screw M5×30 Nut with plate
Four (4) pieces Four (4) pieces
DIMENSIONS
18-11/16"
(Unit: inch)
5-3/16"
6-11/16"
4- 1/4"
17-1/4"
Holes for mounting range hood
5-7/8"
19-11/16"
Duct
3
Make the duct joint secure and
air tight using non-flammable
tape such as duct tape, etc.
(not supplied)
Note: Make sure that the shutter
installed in the exhaust
pipe moves freely.
Range hood unit
3. Connecting Power Supply Wires
WARNING:
• Electrical wiring should be done by a qualified person(s) in
accordance with all applicable codes and standards, including
fire-rated construction. An unqualified person doing the work could
result in fire, electric shock or injury.
• This range hood uses 120V AC. Do not connect to other voltage
since fire, electric shock or damage could result.
1
Remove the nut (not supplied) from
Conduit
the conduit connector at the end of
power wiring.
WARNING:
Nut
Be sure to switch power OFF at
(Not supplied)
service panel before wiring.
2
Connect the conduit through the connecting hole of the enclosure
using the nut previously removed.
Wire box
Nut
3
Connect the electrical wires as follows:
Connect wires tightly and securely using wire connectors
(not supplied).
• Black to Black • White to White • Green to Green
Wires
(conduit side)
Wire connector
(not supplied)
Wires (unit side)
4
Replace the wire cover with the screw removed previously. Make
sure that all wires are connected properly and enclosed inside of
the wiring compartment.
Wire cover
1 Replace the wire cover 2 Slant the wire cover 3 Insert 2 tabs and tighten
with tilting it, and rotate as shown. the screw.
its screw-hole part.
CIRCUIT DIAGRAM
Motor
Fan Switch
Black Grey
Yellow
Red
White
Black
Connector
Connector White
Black
Black
120V White White
60Hz
White
Green
Capacitor
RANGE HOOD LOCATION
1 The range hood must be installed just above the cooktop.
2
The minimum distance from the cooking surface to the bottom of the
range hood must be 24".
Liner
24" (minimum)
Cook top
3
The total weight of the BUF-011/021 range hood unit is 18 lbs. (8 kg)
4
Power requirements are:
BUF-011: AC120 V, 60 Hz, 1.7 Amp
BUF-021: AC120 V, 60 Hz, 2.2 Amp
WARNING:
• Check that the hood is correctly installed, since incorrect installation
could result in the detachment of the range hood and the unit could fall.
CAUTION:
• To protect hands from injury, wear working gloves when installing the
range hood.
4. Final Assembly and Check
Duct tape, etc.
1
Assembly
(1) Replace the front cover with 4 screws.
To prevent the screw holes from being damaged, be sure not
to over tighten the screws (with the torque of 13 inch-lbs. [1.5
N-m] or less).
(2) Replace the filter.
(3) Two 35 Watt halogen light bulbs (not supplied) can be
mounted in this range hood.
Prior to function check, install light bulbs (Bulb type standard
MR16-GU10), rated 120 V-35 Watt or below.
The following light bulbs are recommended for this range
hood.
• GE Model No. Q35GU10/FL/CD
• PHILIPS Model No. Twistline 35W GU10 120V MR16
Turn the lamps clock-wise to install.
Note: When installing the
bulb, be sure to fix to
the socket securely.
Lamp
Conduit Front cover
Lamp
(standard MR16-GU10, 35Watt)
(not supplied)
Filter
2
Check
(1) Turn on the electrical circuit to the range hood.
(2) Make sure that the switch and light operate correctly.
Refer to page 4 of the Operation Manual.
(3) Make sure that the range hood has no abnormal noises and/
or vibration.
Push to turn ON
CAUTION:
• To reduce the risk of injury, keep your hands and other objects away
from the fan while it is in motion.
• Wear working gloves to avoid injury.
5. Explanation to the End User
(1) Referring to the Operation Manual, explain the operation of this
range hood to end users.
(2) The Installation Manual and Operation Manual should be given to
the end user.
Connector
Pilot Lamp
Connector
Yellow
Yellow
Lamp:35W
White
Black
Connector
White
Black
Lamp:35W
Connector
Push the lamp, and
turn it clock-wise.