Fujioh BUF-08P Manuel D'installation

1U03 2781
Model: BUF-08P
SAFETY INSTRUCTIONS
Before installation and operation, read these instructions carefully
and use this product only in the manner described by the
manufacturer in the operation manual.
The instruction shown below are used to alert you to potential
personal injury and property damage hazards.
There are three hazard classifications based on potentially
dangerous situations.
Obey all safety instructions that show these symbols to avoid
possible injury, death and property damage.
WARNING:
WARNING indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION:
CAUTION indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
CAUTION:
CAUTION used without the safety
alert symbol indicates a potentially
hazardous situation which, if not
avoided, may result in property
damage.
NOTE: The safety instructions are explained with the following
pictographic symbols.
means prohibition. It indicates actions, if any, that
mustn't be done.
means forcible execution. It indicates actions, if
any, that must be done.
WARNING
1. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b) Before servicing or cleaning the unit, switch power
off at service panel and lock the service
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.
2. To reduce the risk of fire or electric shock, do not
use this product with any solid-state speed control
device.
3. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Installation work and electrical wiring must be
done by a qualified person(s) in accordance with
all applicable codes and standards, including fire-
rated construction.
1. Preparation
In this manual, the following method is explained as a standard
installation.
There may be some different cases depending on the structure of
the ceiling where the mounting bracket is placed or the shape and
mounting condition of the wood hood.
In such a case, please arrange to find best possible way according
to the condition of the place where the range hood is installed.
WARNING:
• Ensure that the metal duct does not touch other metal housing materials,
otherwise fire or electric shock could result.
Duct
1 Roof cap
This range hood is designed
(For vertical discharge)
to discharge upward. For
Note:
2×7" or 1×10"~12"
vertical discharge, run duct
round duct
works between the hood
location and roof cap location.
To get the best result, use a
minimum number of
transitions and elbows.
Be sure to attach a roof cap
to avoid rain from entering
the exhaust duct.
Soffit
Wood hood Range hood
2 The range hood unit Liner Dimensions
must be mounted to
FWD switches & lamps side
a liner which has
the following
43-3/16" (1096.3)
dimensions. Install
the liner securely
after checking that
the opening size of
the liner is the same
as the figure right.
44" (1117)
Unit: inch (mm)
CAUTION:
• When the liner is installed in the wooden hood, the inside of the wooden
hood placed above the cooking surface must be fully covered by the liner
including bottom edges. Select a suitable liner according to the size and
shape of the wooden hood and install properly.
• The liner should be installed tightly. If the liner installation is not correct,
the range hood unit may become detached and fall.
3
Put 4 all thread rod (∅12~14 anchor bolt, not supplied) into the corner
holes of the mounting bracket, and secure them using washers, spring
washers, and nuts. Place the mounting bracket on the beam of the
ceiling as shown.
Note: The mounting bracket should be securely fastened at this point
to simplify installing the range hood later.
Mounting bracket
Beam
Nut*
Spring-washer*
Washer*
Bracket
*
Not supplied
2. Range Hood Mounting
CAUTION:
• Wear working gloves to avoid injury.
Note: During installation, be careful not to
touch the fan switches. If two or more
switches are pushed at once, it may
be a cause of failure.
1
Place the range hood
as shown and detach
the left and right filters
Front cover
by loosening 2 screws.
Then remove 4 screws
fixing the front cover
and detach the front
cover.
Filter
Loosen 2 screws
Note: Pay attention not
to remove the filter.
to deform the
exhaust ports.
Exhaust
port
INSTALLATION MANUAL
b) Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney)
of fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer's
guidelines and safety standards such as those
published by the National Fire Protection
Association (NFPA), and The American Society
for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code
authorities.
c) When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
d) Ducted fan must always be vented to outdoors.
4. TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
5. This unit must be grounded.
6. Install this range hood to a liner. Check that the
hood is correctly installed, since incorrect
installation could result in the range hood
becoming detached and falling off.
7. Connect only to an AC120 Volt power source or
the range hood could result in fire, electric shock,
and damage.
CAUTION
1. For general ventilating use only. Do not use to
exhaust hazardous or explosive material and
vapors.
2. To reduce the risk of fire and to properly exhaust
air, be sure to duct air outside. Do not vent exhaust
air into spaces within walls, ceilings or into attics,
crawl spaces or garages.
3. Read specification label on this product for further
information and requirements.
4. Use only for the purpose of kitchen ventilation.
5. Do not install this range hood in the bathroom or
in other wet rooms since electrical shock and
damage may result.
6. Fasten the filter and other parts securely. Incorrect
attachment may result in personal injury or
property damage.
7. Keep your hands and other objects away from
the fan while it is in motion. The range hood may
injure you or damage itself.
2
Remove the fan units.
<Attention>
FWD
Clamper
Fan unit Fan unit
Remove this unit first
FWD
(1) Release each fan unit's
wiring clamper.
Fan unit
(2) Remove total 4 screws
from each unit.
Note: Do not remove the keyhole screws.
(3) Remove screws attaching to the top plate.
(4) Disconnect wiring connector coming from the fan unit.
(5) Slide the fan unit rightward to disengage from fixing hook,
then pull it up while avoiding keyhole's screws to remove from
the range hood.
Connector
Push with a
screwdriver etc, FWD
and pull off.
Slide
Hook Remove this side unit
Screw
3
Turn over the range hood and detach
the tape on the exhaust ports.
Detach
4-∅1/4" (4-∅6.5)
the tape.
4
Hold up the range hood,
and with inserting the
exhaust port into the duct,
pass all 4 threaded rods
through the corner holes of
the range hood.
Note:
Do not touch the switch
buttons when holding the
unit as damage may result.
5
Align 4 screw holes of the liner and range hood, then fix securely
using the supplied screws (M5×30) and nuts.
Note: Fasten all the screws and nuts evenly.
[Right & left, each two (2) places]
Nut with plate
Liner
Securing plate
[Securing plate
turns while
passing through
the opening
of Liner]
6
Using washers, spring washers, and double nuts, attach the range
hood to all 4 threaded rods securely.
* Not supplied Enclosure
Washer*
Spring-
Nut*
washer*
Washer*
Use less than ∅1"
washer to avoid
overlapping with
the enclosure bend.
∅ ∅
1"( 25.4)
7
Make the duct joints secure and air-tight using non-flammable tape
such as duct tape, etc. (Not supplied)
Non-flammable tape
Range Hood
NAMES OF PARTS
Pilot Lamp Lamp Switch
OFF Switch High Switch
Low Switch Medium Switch
Lamp (Not supplied)
(PAR20 bulb,
in the base diameter
26mm: medium base)
Front Cover
Fan Switch
(Left)
DIMENSIONS
∅
4- 9/16"
∅
(4- 14.5)
44"(1117)
29-9/16"(750.4)
1/16" (1.5)
∅ ∅
7/8"( 22.6)
43" (1091.6)
31-11/16" (806.4)
10-13/16" (275) 6-1/8" (155)
45" (1143)
30" (762)
12-5/16"(314)
INSTALLATION
Note: If taping from the outside is impossible, remove the exhaust port
Keyhole
Remove second
and insert the duct end to the range hood directly, then make
Remove first
inside taping on the duct end. Be sure to attach a duct cover with
Keyhole
damper in this case.
Duct
Clamper
Exhaust port
3. Connecting Power Supply Wires
WARNING:
• Electrical wiring should be done by a qualified person(s) in accordance
with all applicable codes and standards, including fire-rated construction.
An unqualified person doing the work could result in fire, electric shock
Connector or injury.
Screw
• This range hood uses 120V AC. Do not connect to other voltage since
fire, electric shock or damage could result.
1
Remove the nut from the conduit
connector at the end of power wiring.
Slide
WARNING:
Be sure to switch power OFF
at service panel before wiring.
2
Remove one screw fixing the
wire cover then slide it to detach.
Tape
3
Connect the conduit through
the connecting hole of the
enclosure using the nut
previously removed.
4
Connect wires tightly and securely
using wire connectors (not supplied).
Connect the electrical wires as follows:
• Black to Black
• White to White
• Green to Green
5
Replace the wire cover with
Nut with plate
sliding it as shown and using
the screw removed previously.
Make sure that all wires are
connected properly and
enclosed inside of the wiring
Liner
compartment.
4. Final Assembly and Check
Four screws
(M5×30)
1 Assembly
(1) Attach the fan units respectively by sliding
them leftward to engage with bracket hooks
and keyholes, then tighten screws.
Note: Pass through the wiring over the bracket.
Check that the fan unit is hanged securely on
the keyhole screw and fixing hooks when
CAUTION:
attaching. It may be a cause of injury if dropped.
FWD
Slide
Screw
CIRCUIT DIAGRAM
Enclosure
Fan Switch
(Right)
Lamp Switch
Purple
White
120V
60Hz Black
Green
Filter
Unit: inch (mm)
∅ ∅
4- 1/4"(4- 6)
16-3/4"(425.2)
10-7/16"
(265.4)
RANGE HOOD LOCATION
∅ ∅
6-15/16"( 176)
1
The range hood must be installed just
above the cooktop.
2
The minimum distance from the
cooking surface to the bottom of the
range hood must be 24".
17-1/2"(453.6)
3
The total weight of the BUF-08P
range hood unit is 70.4 lbs. (32 kg)
4
Power requirements are:
AC120 V, 60 Hz, 5.8 Amp
CAUTION:
• Check that the hood is correctly installed, since incorrect installation
could result in the detachment of the range hood and the unit could fall.
• To protect hands from injury, wear working gloves when installing the
range hood.
(2) Fix each fan unit using the
removed screws.
Range hood
Non-flammable
tape
Duct
(3) Connect each fan unit's
wiring connector.
Note: Be sure to connect
firmly as illustrated.
(4) Fasten each fan unit's
wiring clamper.
(5) Attach the front cover, and secure
Conduit
it with 4 screws.
(Not supplied)
Then attach the filters.
Nut
(Not supplied)
Hook
Wire cover
(6) Three 50 Watt halogen light bulbs (not supplied)
can be mounted in this range hood.
Prior to function check, install
light bulbs (PAR20 bulb, with
base diameter 26 mm: medium
base), rated at 120 V - 50 Watt
or below.
The following light bulbs are recommended for this range hood.
• GE Model No. 50PAR20H/FL25
• SYLVANIA Model No. 50PAR20/HAL/DL/NFL
Turn the lamps clock-wise to install.
2
Check
(1) Turn on the electrical circuit to the range hood.
(2) Make sure that the switches and light operate correctly.
Refer to page 4 of the Operation Manual.
(3) Make sure that the range hood functions properly and it has
no abnormal noises and/or vibration.
Push to
turn ON
FWD
Fan unit Fan unit
Attach this unit first
Attach this side unit
Hook
5. Explanation to the End User
(1) Referring to the Operation Manual, explain the operation of this range
hood to end users.
(2) The Installation Manual and Operation Manual should be given to the
Slide
end user.
Fan unit
Keyhole
Wire Bracket
Lamp Switch
Fan Switch
Connector
Black
Black
Pilot Lamp
Grey
Black
Yellow Black Lamp:50W
Black White
Motor
White
Black
Black
Connector
White
Connector
White
Black
Black
Connector
White
Lamp:50W
Connector White
Black
Black
Connector
Lamp:50W
White
Grey Purple Grey
Black
Capacitor
Purple Red
Yellow
Yellow Black
Grey
Black
Black
Connector Pilot Lamp
Connector
Motor
Fan Switch
ACCESSORIES
Mounting bracket Screw M5×30
One (1) piece Four (4) pieces
Nut with plate
Four (4) pieces
Liner
24" (Minimum)
Cook top
FWD Connector
Connector
Clamper
Clamper
Screw
Filter
Front cover
Bulb
(Not supplied)
Fan Switch Lamp Switch
Turn the switch
clockwise