Fujioh BUF-08W Instructions D'installation

1U03 2681
Model: BUF-08W
SAFETY INSTRUCTIONS
Before installation and operation, read these instructions carefully
and use this product only in the manner described by the
manufacturer in the operation manual.
The instruction shown below are used to alert you to potential
personal injury and property damage hazards.
There are three hazard classifications based on potentially
dangerous situations.
Obey all safety instructions that show these symbols to avoid
possible injury, death and property damage.
WARNING:
WARNING indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION:
CAUTION indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
CAUTION:
CAUTION used without the safety
alert symbol indicates a potentially
hazardous situation which, if not
avoided, may result in property
damage.
NOTE: The safety instructions are explained with the following
pictographic symbols.
means prohibition. It indicates actions, if any,
that mustn't be done.
means forcible execution. It indicates actions, if
any, that must be done.
WARNING
1. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b) Before servicing or cleaning the unit, switch power
off at service panel and lock the service
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.
2. To reduce the risk of fire or electric shock, do not
use this product with any solid-state speed control
device.
3. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Installation work and electrical wiring must be
done by a qualified person(s) in accordance with
all applicable codes and standards, including fire-
rated construction.
1. Preparation
WARNING:
• Ensure that the metal duct does not touch other metal housing
materials, otherwise fire or electric shock could result.
Roof cap Duct
(For vertical discharge)
1
This range hood is designed to
Note:
discharge upward. For vertical
2×7" or 1×10"~12"
round duct
discharge, run duct works
between the hood location and
roof cap location.
To get the best result, use a
Soffit
minimum number of transitons
and elbows.
Be sure to attach a roof cap to
avoid rain from entering the
exhaust duct.
Range hood
2
The range hood unit must be mounted to a liner which has the
following dimensions. Install the liner securely after checking that
the opening size of the liner is the same as the figure below.
FWD switches & lamps side
43-3/16" (1096.3)
4-∅1/4" (4-∅6.5)
44" (1117)
Unit: inch (mm)
CAUTION:
• When the liner is installed in the wooden hood, the inside of the
wooden hood placed above the cooking surface must be fully covered
by the liner including bottom edges. Select a suitable liner according
to the size and shape of the wooden hood and install properly.
• The liner should be installed tightly. If the liner installation is not
correct, the range hood unit may become detached and fall.
Wood panel
3
Make sure that a wood panel for mounting
the range hood is fixed on the wall where
the range hood is installed.
Note: If no wood panel is found on the
wall, be sure to prepare one
Fan unit
referring to the figure.
Liner
2. Range Hood Mounting
CAUTION:
• Wear working gloves to avoid injury.
Note: During installation, be careful not to
touch the fan switches. If two or more
switches are pushed at once, it may
be a cause of failure.
1
Place the range hood
as shown and detach
the left and right filters
by loosening 2 screws.
Front cover
Then remove 4 screws
fixing the front cover
and detach the front
cover.
Filter
Note: Pay attention
Loosen 2 screws
not to deform
to remove the filter.
the exhaust
Exhaust
ports.
port
Range Hood
INSTALLATION MANUAL
b) Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney)
of fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer's
guidelines and safety standards such as those
published by the National Fire Protection
Association (NFPA), and The American Society
for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code
authorities.
c) When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
d) Ducted fan must always be vented to outdoors.
4. TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
5. This unit must be grounded.
6. Install this range hood to a liner. Check that the
hood is correctly installed, since incorrect
installation could result in the range hood
becoming detached and falling off.
7. Connect only to an AC120 Volt power source or
the range hood could result in fire, electric shock,
and damage.
CAUTION
1. For general ventilating use only. Do not use to
exhaust hazardous or explosive material and
vapors.
2. To reduce the risk of fire and to properly exhaust
air, be sure to duct air outside. Do not vent exhaust
air into spaces within walls, ceilings or into attics,
crawl spaces or garages.
3. Read specification label on this product for further
information and requirements.
4. Use only for the purpose of kitchen ventilation.
5. Do not install this range hood in the bathroom or
in other wet rooms since electrical shock and
damage may result.
6. Fasten the filter and other parts securely. Incorrect
attachment may result in personal injury or
property damage.
7. Keep your hands and other objects away from
the fan while it is in motion. The range hood may
injure you or damage itself.
2
Remove the fan units.
Keyhole
<Attention>
FWD
Fan unit Fan unit
Clamper
Remove this unit first
(1) Release each fan unit's
FWD
wiring clamper.
(2) Remove total 4 screws
Fan unit
from each unit. Clamper
Note: Do not remove the keyhole screws.
(3) Remove screws attaching to the top plate.
(4) Disconnect wiring connector coming from the fan unit.
(5) Slide the fan unit rightward to disengage from fixing hook,
then pull it up while avoiding keyhole's screws to remove from
the range hood.
Connector
Push with a
screwdriver etc,
FWD
and pull off.
Hook
Slide
Screw
Remove this side unit
Screw
3
Turn over the range hood
Detach the tape.
and detach the tape on
Tape
the exhaust ports.
4
Hold up the range hood and with inserting the exhaust ports into
the ducts, align the 4 screw holes of the liner and range hood,
then fix securely using the supplied screws (M5×30) and nuts.
Note: • Fasten all the screws and nuts evenly.
• Do not touch the switch buttons when hold up. Because if
some buttons are pushed simultaneously, it may be a
Wall
cause of failure.
Liner
Nut with plate
[Right & left, each two (2) places]
Securing plate
[Securing plate
turns while
passing through
the opening
of Liner]
Four screws
(M5×30)
5
Fix the range hood securely
using 4 supplied wood screws
(M4.5×45) to the holes on the
back of the range hood.
6
Make the duct joints secure and
air-tight using non-flammable
tape such as duct tape, etc.
(Not supplied)
Non-flammable tape
NAMES OF PARTS
Pilot Lamp Lamp Switch
OFF Switch High Switch
Low Switch Medium Switch
Lamp (Not supplied)
(PAR20 bulb, in the base
diameter 26mm:
medium base)
Front Cover
Fan Switch
(Left)
DIMENSIONS
44"(1117)
∅ ∅
4- 1/4"(4- 6)
∅ ∅
7/8"( 22.6)
16-3/4"(425.5)
10-7/16"(265.4)
43" (1091.6)
31-11/16" (806.4)
10-13/16" (275) 6-1/8" (155)
17-1/2"(453.6)
45" (1143)
30" (762)
12-5/16"(314)
INSTALLATION
3. Connecting Power Supply Wires
Remove second
Remove first
WARNING:
Keyhole
• Electrical wiring should be done by a qualified person(s) in
accordance with all applicable codes and standards, including fire-
rated construction. An unqualified person doing the work could result
in fire, electric shock or injury.
• This range hood uses 120V AC. Do not connect to other voltage
since fire, electric shock or damage could result.
1
Remove the nut from the conduit
connector at the end of power wiring.
WARNING:
Be sure to switch power OFF at service panel before wiring.
2
Remove one screw fixing
the wire cover then slide it
to detach.
Connector
3
Connect the conduit through
Slide the connecting hole of the
enclosure using the nut
previously removed.
4
Connect wires tightly and securely using
wire connectors (not supplied).
Connect the electrical wires as follows:
• Black to Black
• White to White
• Green to Green
5
Replace the wire cover with sliding it as
shown and using the screws removed
previously. Make sure that all wires are
connected properly and enclosed inside
of the wiring compartment.
Nut with plate
Liner
4. Final Assembly and Check
1
Assembly
(1) Attach the fan units respectively by
sliding them leftward to engage with
bracket hooks and keyholes, then
tighten screws.
Note: Pass through the wiring over the
bracket.
Check that the fan unit is hanged securely on
CAUTION:
the keyhole screw and fixing hooks when
attaching. It may be a cause of injury if dropped.
FWD
Tighten screws
to fix
Slide
Screw
Enclosure
Fan Switch
(Right)
Lamp Switch
White
120V
60Hz Black
Green
Filter
Unit: inch (mm)
RANGE HOOD LOCATION
5-11/16"(145)
1
The range hood must be installed just above the cooktop.
∅ ∅
6-15/16"( 176)
9/16"(14)
2
The minimum distance
from the cooking surface
to the bottom of the range
hood must be 24".
31-1/2"(800) 3
The total weight of the
33-7/8"(860)
BUF-08W range hood unit
is 68.2 lbs. (31 kg)
4
Power requirements are:
AC120 V, 60 Hz, 5.8 Amp
CAUTION:
• Check that the hood is correctly installed, since incorrect installation
could result in the detachment of the range hood and the unit
could fall.
• To protect hands from injury, wear working gloves when installing
the range hood.
(2) Fix each fan unit using the
removed screws.
(3) Connect each fan
unit's wiring connector.
Conduit
(Not supplied)
Note: Be sure to connect
firmly as illustrated.
Nut
(4) Fasten each fan unit's
(Not supplied)
wiring clamper.
Hook
(5) Attach the front cover, and
secure it with 4 screws.
Wire cover
Then attach the filters.
(6) Three 50 Watt halogen light bulbs (not supplied)
can be mounted in this range hood.
Prior to function check, install
light bulbs (PAR20 bulb, with
base diameter 26 mm: medium
base), rated at 120 V - 50 Watt
or below.
The following light bulbs are
recommended for this range
hood.
• GE Model No. 50PAR20H/FL25
• SYLVANIA Model No. 50PAR20/HAL/DL/NFL
Turn the lamps clock-wise to install.
2
Check
(1) Turn on the electrical circuit to the range hood.
(2) Make sure that the switchs and light operate correctly.
Refer to page 4 of the Operation Manual.
(3) Make sure that the range hood functions properly and it has
FWD
no abnormal noises and/or vibration.
Fan unit Fan unit
Attach this unit first
Attach this side unit
Fan unit
Hook
5. Explanation to the End User
Wire
Bracket
(1) Referring to the Operation Manual, explain the operation of this range
Slide Keyhole
hood to end users.
(2) The Installation Manual and Operation Manual should be given to
the end user.
CIRCUIT DIAGRAM
Lamp Switch
Fan Switch
Connector
Black
Black
Pilot Lamp
Grey Black
Lamp:50W
Yellow Black
Black White
Motor
White
Black
Black
Connector
White
Connector
White
Black
Black
Connector
White
Lamp:50W
Connector White
Black
Black
Connector
Lamp:50W
White
Purple
Grey Purple Grey
Black
Capacitor
Purple Red
Yellow
Yellow Black
Grey
Black
Black
Connector Pilot Lamp
Connector
Motor
Fan Switch
ACCESSORIES
Screw M4.5×45 Nut with plate
Four (4) pieces Four (4) pieces
Screw M5×30
Four (4) pieces
Liner
24" (Minimum)
Cook top
FWD
Connector
Connector
Clamper
Clamper
Screw
Filter
Front cover
Bulb
(Not supplied)
Fan Switch Lamp Switch
Push to
turn ON
Turn the switch
clockwise