Taurus LIQUAJUICE LS-651 BM Mode D'emploi page 8

UTILIZATION
- Wash the fruit and /or vegetable and cut them
into pieces that fit into the feeding tube.
- Please make sure that the switch is turned at
"O" before to connect to the power.
- Connect the appliance to the mains.
- Put the juicer cup and residue cup under the
juice and dregs spout
- The switch has 3 positions
- ON starts the machine and juicing process
- STOP is the central position of the button. It
stops the appliance
- REV is REVERSE. It is a function to be
used when something is stuck in the juicer
and it needs to be unclogged. Finger should
keep pressing this button while it start
working.
- Prepare the material you wish to juice. The
slow juicer is designed to juice many different
materials
- The necessary preparation will be different
depending on the used materials
- If you use small mouth juicing, ensure juice
material is cut small portion for optimal juice
extraction
- Each portion should easily fall down the hopper
chute without the need for force
- If big mouth juicing, ensure the diameter of the
fruit is less than 5.5 cm
- Turn the appliance on, by turning the control
knob to setting "ON"
- Insert pre-cut pieces slowly in the feeding tube
and allow juicer have time to work.
- Don't overstuff the hopper or force food in
- Only use the aid of the pusher when necessary
- Remark: If you process a large quantity of fruit,
you must periodically clean the filter and remove
the remains of the pulp.
NOTES:
- This product is only used for extract juice.
- Peel only the ingredients with thick skin such as
citrus fruits, bananas, pineapples, melon and
so on.)
- Remove the kernel from the fruits such as
plums, peaches, cherries, apricots and so on)
- Other fruit with soft peel should be washed be-
fore extracting such as apples, carrots, grapes,
strawberry and so on.)
- Never put fruit kernel, excessively hard foods
(ice cubes, sugar cubes), extremely fibrous food
or meat into your juicer because they would
damage the filter net and pusher.
All manuals and user guides at all-guides.com
- Switch "ON" stand for rotating clockwise, switch
R stands for rotating reversely, switch "O"
stands for stop. When there is some fruits be
stuck between filter net and pusher, please turn
the switch to speed "R" to make the fruit exit,
then turn the switch to ON for extracting.
- Put the fruits into the feeding chute slowly, and
using the pusher to push it.
NOTES:
- Please do not put your fingers or other ob-
jects to the feeding chute is blocked, please
use the pusher or other fruit slice to push
and remove the stuck fruit. If it still won´t
work, stop the machine and clean up the
stuck fruit.
- Turn the switch to "O" if the juice cup or dregs
is full, please also turn off the machine if there
is no fruit. Empty the cup and clean the filter net
and feeding chute for the next extracting.
ADVICE:
- Before finishing or between different juices
- To facilitate cleaning, we recommend pre-
wash. To do this, switch-ON the appliance,
and previously placing the jug of juice in its
outlet, operate the appliance with only water.
- With closed juice outlet, insert water through
the food inlet. When you consider is enough,
stop and open the cap (L) to empty water.
So, it will facilitate the subsequent cleaning
ONCE YOU HAVE FINISHED USING THE
APPLIANCE:
- Turn the appliance off, using the on/off switch.
- Unplug the appliance from the mains.
- Clean the appliance.
HOW TO DISASSEMBLE AND CLEAN THE
UNIT
- Switch off the unit
- Unplug the appliance from the mains.
- Twist the hopper anticlockwise then lift off. Lift
the bowl straight up to remove from the base
- Disassemble the parts from the juicing bowl in
the following order:
- Auger (C), Filter (D1), Spinning brush (D2),
Juice bowl (E)
- Use the brush to clean all these parts.
- Ensure pulp outlet is clear and unplug the
rubber stopper(M) (Fig 1) for easier access to
pulp outlet