Bosch GKT 55 GCE Professional Notice Originale page 16

16 | English
28 Set of screw clamps*
29 Guide rail*
30 Connection piece*
31 Vacuum hose*
32 Cutting mark, 0°
33 Cutting mark, 45°
34 Plastic insert for base plate
35 Knurled screws for play adjustment of guide groove
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Circular Saw
Article number
Rated power input
No-load speed
Rotational speed under load, max.
Cutting depth, max.
– for 0° bevel angle
– for 45° bevel angle
Spindle lock
Speed preselection
Constant electronic control
Reduced starting current
Base plate dimensions
Saw blade diameter, max.
Saw blade diameter, min.
Blade thickness, max.
Tooth thickness/setting, max.
Tooth thickness/setting, min.
Mounting bore
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-5.
Typically the A-weighted noise levels of the product are:
Sound pressure level 92 dB(A); Sound power level
103 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
Cutting wood: a <2.5 m/s
h
Cutting metal: a <2.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
1 609 92A 14W | (21.1.15)
GKT 55 GCE
3 601 F75 0..
W
-1
min 3600 – 6250
-1
min
mm
mm
mm 154 x 305
mm
mm
mm
mm
mm
mm
kg
2 2
, K=1.5 m/s ,
2 2
, K=1.5 m/s .
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
1400
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU,
5900
2004/108/EC, 2006/42/EC including their amendments
and complies with the following standards: EN 60745-1,
57
EN 60745-2-5.
42
Technical file (2006/42/EC) at:

Robert Bosch GmbH, PT/ETM9,

70764 Leinfelden-Echterdingen, GERMANY

Henk Becker
Executive Vice President

Engineering
165
160
1.8
Robert Bosch GmbH, Power Tools Division
2.6
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 21.01.2015
1.8
20
Assembly
4.7
Mounting/Replacing the Saw Blade
/ II
 Before any work on the machine itself, pull the mains
plug.
 When mounting the saw blade, wear protective gloves.
Danger of injury when touching the saw blade.
 Only use saw blades that correspond with the charac-
teristic data given in the operating instructions.
 Do not under any circumstances use grinding discs as
the cutting tool.
Selecting a Saw Blade
An overview of recommended saw blades can be found at the
end of this manual.
Removal of the Saw Blade (see figure A)
Adjust the maximal cutting depth, see section "Adjusting the
Cutting Depth".
For changing the cutting tool, it is best to place the machine
on the face side of the motor housing.
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Bosch Power Tools