Publicité
Les langues disponibles
Les langues disponibles
Operating Instructions
Bilge Pump with Sensor 12 V, 3 A, 2839 l/h
Item No. 2386376
Intended use
The product is an ignition protected submersible bilge pump. It has an integrated float switch
and removable filter basket for maintenance. Only for use with fresh water or salt water.
NOTE
• The product has an IPX8 ingress protection rating and is suitable for outdoor use.
• The product is sealed and submersible.
• Please read the included safety instructions.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged. In
addition, improper use can result in short circuits, fires, or other hazards. Read the instruc-
tions carefully and store them in a safe place. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Product
• Operating instructions
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or
scan the QR code shown. Follow the instructions on the website.
Explanation of symbols
The symbol with the exclamation
mark in the triangle is used to indi-
cate important information in these
operating instructions. Always read
this information carefully.
This product is constructed accord-
ing to protection class III.
The arrow symbol indicates special
information and advice on opera-
tion.
Safety instructions
Read the operating instructions
carefully and especially observe
the safety information. If you do
not follow the safety instructions
and information on proper han-
dling in this manual, we assume
no liability for any resulting per-
sonal injury or damage to prop-
erty. Such cases will invalidate
the warranty/guarantee.
a) General information
• The device is not a toy. Keep it out of the
reach of children and pets.
• Do not leave packaging material lying
around carelessly. This may become dan-
gerous playing material for children.
• Protect the appliance from extreme tem-
peratures, strong jolts, flammable gases,
steam and solvents.
• Do not place the product under any me-
chanical stress.
All manuals and user guides at all-guidesbox.com
• If it is no longer possible to operate the
product safely, take it out of operation and
protect it from any accidental use. Safe
operation can no longer be guaranteed if
the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in
poor ambient conditions or
- has been subjected to any serious trans-
port-related stresses.
• Please handle the product carefully. Jolts,
impacts or a fall even from a low height can
damage the product.
• Consult an expert when in doubt about the
operation, safety or connection of the ap-
pliance.
• Maintenance, modifications and repairs
must only be completed by a technician or
an authorised repair centre.
• If you have questions which remain un-
answered by these operating instructions,
contact our technical support service or
other technical personnel.
b) Connected devices
• Also observe the safety and operating in-
structions of any other devices which are
connected to the product.
Overview
Figure 1
Outlet nozzle
Outlet nozzle
pointing to
pointing to
transom
transom
Float end of
Float end
pump
of pump
Towards bow
Towards bow
Mounting block:
Mounting block:
25.4mm (1")
25.4 mm (1")
Figure 2
Fuse
Fuse
holder
holeder
Figure 3
Remove screws
Remove screws
Filter basket
Filter basket
Installation
See figure 3.
IMPORTANT!
• The filter basket must be properly attached before running the pump. Do not over-
tighten the screws.
• The thru-hull fitting should be at least 30 cm (12") above the water line to prevent
water from flowing back into the pump outlet when the pump is switched off.
a) Location
Determine the best location.
• If installing one pump it should be placed where the water is deepest when the boat stops.
• Make sure the pump body can be removed for cleaning in this position.
b) Mounting
1. Press the release tabs to remove the filter basket.
2. Mount the filter basket.
- Attaching to wood block: use marine grade stainless steel self-tapping screws.
- Attaching to metal or glass fiber: install a piece of wood first, then fix to the wood.
3. Mark the mounting location of the three mounting holes with a pencil or scribe.
4. Carefully drill two ø3.18 mm (1/8") pilot holes in marked area and drive a screw in each hole.
Transom
Transom
Level
Level
Parallel to bottom
Parallel to bottom
of boat
of boat
Black
Black
Brown
Brown
Brown
Brown
Off
Off
Brown / white
Automatic
Automatic
Brown/white
Test knob
Test knob
3-way switch
3-way switch
Outlet nozzle
Outlet nozzle
Impeller
Impeller
guard
guard
Release tabs
Release tabs
Publicité
