UFESA GS1600 Manuel D'utilisation page 15

AF-Manual-PLANCHA VERTICAL GS1600.pdf
BEFORE THE FIRST USE
BEFORE THE FIRST USE
In the first use they can break o odors or fumes that sent quickly. Do not spray for the first time on
clothes and there may be traces of dirt on the steam head.
clothes and there may be traces of dirt on the steam head.
FILLING WITH WATER
FILLING WITH WATER
Remove the mains plug from the wall socket before filling or emptying the garment. (Fig.1) To remove
the water tank (E), turn it from locked position to unlocked position and pull it firmly away from the
garment steamer main body. (Fig.3) Open the silicon cap (F) and fill in up to the max. (Fig. 4). Make sure
garment steamer main body. (Fig.3)
that the silicone cap is correctly closed. Once full, refit the water tank (Fig. 5). Refill the water tank as and
when required. One max. fill o ers approx. 8-10 minutes of continuous use.
When removing the water tank, take care not to touch the steam head (B).
When removing the water tank, take care not to touch the steam head (B).
Your appliance was designed to operate using untreated tap water. Do not use pure demineralized or
Your appliance was designed to operate using untreated tap water. Do not use pure demineralized or
pure distilled water, water from clothes dryers, scented or softened water, rain water, filtered, bottled or
boiled water, water from refrigerators, batteries or air conditioners as these may damage the appliance.
boiled water, water from refrigerators, batteries or air conditioners as these may damage the appliance.
These types of water contain organic waste, mineral elements that become concentrated when heated
These types of water contain organic waste, mineral elements that become concentrated when heated
and cause spitting, brown staining, leaking or premature wear on your appliance. If your water is very
and cause spitting, brown staining, leaking or premature wear on your appliance. If your water is very
hard, mix 50% untreated tap water with 50% distilled water. Make sure the silicone cap is correctly
hard, mix 50% untreated tap water with 50% distilled water. Make sure the silicone cap is correctly
closed before attaching the handle to the main unit.
closed before attaching the handle to the main unit.
C
M
HOW TO USE
HOW TO USE
Y
Before using, please check fabric´s label for recommendations.
CM Before using, please check fabric´s label for recommendations.
We recommended that you test acrylic, nylon or other synthetic fabrics in a hidden area to ensure these
We recommended that you test acrylic, nylon or other synthetic fabrics in a hidden area to ensure these
MY
fabrics are not damaged by hot steam.
fabrics are not damaged by hot steam.
CY
If required, secure the brush attachment (A) by clicking it into place on the steam head (B). Make sure
If required, secure the brush attachment (A) by clicking it into place on the steam head (B). Make sure
that the brush attachment is the right way up, and that the steam holes are not blocked. (Fig.2).
that the brush attachment is the right way up, and that the steam holes are not blocked. (Fig.2).
CMY
Warning: always allow the garment steamer to cool down before adding or removing the brush
Warning: always allow the garment steamer to cool down before adding or removing the brush
K
attachment from the steam head.
attachment from the steam head.
1. Hang the garment to be steamed on a clothes hanger.
1. Hang the garment to be steamed on a clothes hanger.
2. Place the garment steamer onto a flat, stable surface, and switch it on at the mains power supply. The
garment steamer will start to heat up once it is plugged in. The indicator light (C) will switch on in red
garment steamer will start to heat up once it is plugged in. The indicator light (C) will switch on in red
colour showing that the garment steamer is preheating.
colour showing that the garment steamer is preheating.
3. After approximately 30 seconds of preheating, the indicator light will switch on in green colour
3. After approximately 30 seconds of preheating, the indicator light will switch on in green colour
showing that the garment steamer has reached the required temperature.
showing that the garment steamer has reached the required temperature.
4. To begin steaming, face the steamer against the fabric keeping a certain distance, and press the
4. To begin steaming, face the steamer against the fabric keeping a certain distance, and press the
trigger (D). You can keep the trigger continuously pressed by sliding the locking lever. Carefully steam
trigger (D). You can keep the trigger continuously pressed by sliding the locking lever. Carefully steam
the garment using long, straight, downwards movements to remove any wrinkles or creases. (Fig. 6).
the garment using long, straight, downwards movements to remove any wrinkles or creases. (Fig. 6).
5. Once the garment has been steamed, release the steam trigger (D) and then switch o and unplug the
5. Once the garment has been steamed, release the steam trigger (D) and then switch off and unplug the
garment steamer from the mains power supply.
garment steamer from the mains power supply.
Important notice: you can replace the detachable water tank (E) by the included bottle adaptor (G). You
Important notice: you can replace the detachable water tank (E) by the included bottle adaptor (G). You
can use it with any bottle filled with tap water, which is more convenient to storage the appliance and
save space at your luggage when travelling.
save space at your luggage when travelling.
Warnings:
Warnings:
• Never point the steam jet at garments being worn, or at people or animals.
• Do not hold the garment steamer by any other part of the unit except the handle.
• Do not hold the garment steamer by any other part of the unit except the handle.
• During operation, the garment steamer will get very hot. Please take maximum care.
• During operation, the garment steamer will get very hot. Please take maximum care.
15 11/3/21 11:26
All manuals and user guides at all-guidesbox.com
To remove
The
15