Publicité
Les langues disponibles
Les langues disponibles
[COAX TRANSM. / AUX LINE
[----------------------------]
[ 1.Coax Transmission: NO
[ 2.Aux Line: TELEM.MACRO
[ 3.Aux Baudrate: 384OO
[
[
[
[
[
[
[SEQ.End
[VIDEO
[----------------------------]
[
[ 1.System: PAL
[ 2.Interlaced: YES
[
[
[
[
[
[
[SEQ.End
[CYCLE SEQUENCES
[----------------------------]
[ 1. Day seq,
Output 1
[ 2. Day seq,
Output 2
[ 3. Day seq,
Output 3
[ 4. Day seq,
Output 4
[ 5.Night seq, Output 1
[ 6.Night seq, Output 2
[ 7.Night seq, Output 3
[ 8.Night seq, Output 4
[
[SEQ.End
[CYCLE SEQUENCES
[----------------------------]
[ 1.Output 1
[ 2.Output 2
[ 3.Output 3
[ 4.Output 4
[
[
[
[
[
[SEQ.End
[OUTPUT 1
[----------------------------]
[Step: Cam Time
[ > A:
1
2
[
B:
2
2
Step:
[
C:
3
2
INC.Previous ]
[
D:
4
2
DEC.Next
[
[----------------
[1..16.Camera
[ENTER/CLEAR.Change Time
[SEQ.End
All manuals and user guides at all-guides.com
2.7]
Coax and Aux Line Transmission Submenu
]
The matrix is able to transmit telemetry commands via coaxial cable and to
]
control both telemetry receivers and video multiplexers using the Aux line.
]
]
]
Press
to enable/disable transmission via coaxial cable.
]
Press
to select the protocol for the Aux line.
]
]
Press
to choose the baud rate.
]
]
Protocol Pelco D/Eneo is used in a wide range of domes and receivers. These
objects don't move at the same speed and it can be useful to change speed
factors when speeds are too high or movement is not smooth enough.
It is recommended to try the four available speed factors and then choose the
one that allows better movements.
Please note: to be able to use transmission via coaxial cable or along the Aux
line, it is necessary to set the MACRO protocol towards the keyboards! Any
other protocol will not allow the Coax and Aux lines to transmit the intended
messages.
2.8]
Video Submenu
]
Press
to change the type of video code system: Pal or NTSC.
]
]
]
Press
to change the type of output video signal in On Screen Menu mode.
]
Interlaced setting: No, for greater text stability. However, for some types of
]
]
monitor (digital types in particular) the function may cause image compression
]
problems; in which case set interlaced to: Yes.
]
]
3]
Cycle sequences submenu (night-time and daytime)
]
The cycle sequences submenu may be shown in different formats, depending
]
on whether night-time sequences have been enabled and on the number of
]
output videos the matrix has.
]
]
Night-time video sequences are only present if their use has been enabled. If
]
not a simplified menu is shown as in the next section.
]
Press
...
to proceed with switching sequence modification, or
]
]
return to the main menu. (See section 4.1.2)
]
3]
Cycle sequences submenu (only daytime)
]
If the night-time sequences are not used (a single sequence is used for each
]
output for the complete 24-hour day, without differences for working days and
]
holidays) a simplified menu is shown.
]
]
Press
...
to select the desired sequence or
]
menu. (See section 4.1.2)
]
]
]
]
3.1]
Sequence Modify submenu
]
Each cycle sequence consists of a max. of 16 steps, each of which is defined
]
by an input video to be viewed, and by the viewing time in seconds. The
]
screen shows only 4 steps at a time while the others can be requested by
]
pressing
and
]
The cursor > indicates the step being modified: press the desired camera
]
]
number, and increase/decrease the viewing time with
]
When sequence definition is complete, press
]
previous menu.
Pag. 25
.
to
to return to the main
/
.
to confirm and return to the
MNNAEKR_0408
Publicité
