BorMann BCD2640 Mode D'emploi page 6

E N
Charging indicator
The charger is designed to detect some problems that can arise with battery packs. Indicator lights indicate problems (see table below). If this occurs, insert
a new battery pack to determine if the charger is faulty. If the new battery charges correctly, then the original battery is defective and should be returned
to a service center or recycling service center. If the new battery pack displays the same problem as the original battery Pack, have the charger tested at an
authorized service center.
Removing or installing the battery pack (Fig. B)
Depress the battery pack release button to release and slide the battery pack out from the tool. After recharging, slide it back into the tool. A simple push and
slight pressure will be sufficient.
Assembly
Assembling the sanding paper (Fig. C)
1. Remove any dust or other objects from the sanding plate and sandpaper.
2. The sandpaper has dust extraction holes that must be aligned with the holes in the sanding plate, otherwise the dust extraction will not function.
Fitting and removing the dust bag (Fig. D)
Attaching the dust bag
• The sander is equipped with a dust bag.
• To attach, slide the dust bag onto the dust outlet at the rear of the sander.
Warning: To protect your face and eyes from dust, never attempt to use the sander without the dust bag properly installed.
Emptying the dust bag (Fig. E1, E2)
• For more efficient operation, empty the dust bag every 5-10mins.
• To empty the dust bag, first remove it from the dust extraction outlet, and then you can shake the dust out.
Attaching a dust collector vacuum to the sander (Fig. F)
• The sander is equipped with a vacuum adapter which is designed for collecting dust.
• Insert the vacuum adapter into the rear dust extraction outlet and ensure it is tightened securely. Then, connect the adapter to the hose of a vacuum cleaner.
• While using, first turn on the vacuum cleaner, and then turn on the sander.
• When you stop sanding, first turn off the sander, then turn off the vacuum cleaner.
Note: Always connect the adaptor with a 35mm vacuum hose.
Placing the polishing pad (Fig. G1, G2)
• The machine is equipped with a polishing pad.
• Place the polishing pad securely on the rotary plate and make sure it's centrosymmetric. Otherwise the polisher will vibrate intensely.
Operation
ON/OFF switch
• To turn on the sander, depress the protective cover over the switch at the position marked "I".
• To turn off the sander, depress the protective cover at the position marked "0".
Variable speed control
• With the variable speed control, the required speed can be selected (also while the sander is turned on).
• The required speed is dependent on the material and is to be determined by a practical trial.
Hand grip area
• The sander is designed to be held by the top of the main housing.
Using the sander
• The workpiece to be sanded must be secured. If it is small or is likely to move during sanding, it must be held in a vise or suitably clamped.
• Be sure to hold the sander firmly whilst it is turned on and gently move it towards the surface of the work piece. Hold the sander so that it is flat on the
workpiece and utilize slow, smooth and circular motions.
• Regularly check the condition of the sanding paper and replace when worn for best results.
Rough sanding
• Attach a sand paper with coarse grain.
• Apply only light pressure on the workpiece to achieve increased material removal.
Fine sanding
• Attach a sand paper with fine grain.
• Applying moderate pressure, move the machine in a circular pattern or alternately in lengthwise and crosswise directions over the workpiece.
• Do not tilt the machine to avoid leaving marks on the workpiece (e.g. when sanding veneer).
• After finishing the work, switch off the machine and lift it from the workpiece.
Orbital sanding
• Guide the sander parallel to the working surface and move it in circles or in a cross pattern.
• Do not tilt the tool in order to avoid deep unwanted sanding marks.
• The amount of material removed is determined by the speed of the sanding disc and the grit size used. The speed of the sanding disc diminishes depending
on the amount of pressure applied to the workpiece with the sander.
• For best results, do not increase pressure on the tool, but use a coarser grit size.
6
Light Status
Red on Charging
Green on Fully charged
WWW.NIKOLAOUTOOLS.GR