VONROC MS506AC Traduction De La Notice Originale page 15

using the handle and afterwards push the handle
(2) towards the fence (9) and saw through the
workpiece with uniform feed.
For small workpieces, it is possible to fix the sliding
function in the rear position of the saw with the
locking bolt for slide rails (29). If more cutting
width is desired, then it is necessary to loosen the
locking bolt for slide rails (29).
Adjusting the depth stop (Fig. N)
The depth stop can be adjusted, to limit the cutting
depth. This can be used to easily saw a groove. To
do so:
1. Move the plate for depth adjustment (45) to the
left.
2. Adjust the knob for depth adjustment (24) to
the desired depth;
Switching the laser on/off (Fig. G, O)
Press the laser switch (46) to switch the laser on
or off.
Fine-tuning
Prior to any adjustment work disconnect
the mains power plug.
To ensure precise cuts, the basic settings of the
saw must be checked and adjusted before first use,
as well as necessary after intensive use. Suitable
special tools are required for this. Ferm after-sales
will help handling this work quickly and reliably.
Fine-tuning the laser (Fig. O)
If the laser (18) ceases to indicate the correct cut-
ting line, you can readjust the laser. To do so:
• Loosen the laser adjustment screws (48) and
set the laser by moving it until the laser beam
strikes the teeth of the saw blade (6).
Fine-tuning the 0° bevel angle (Fig. P, Q)
1. Adjust the mitre and bevel angle to 0°;
2. Lower the handle (2) and secure it using the
position lock knob (38);
3. Lock the slide movement using the locking bolt
for slide rails (29);
4. Set an angle gauge to 90° and place it on the
table (11), as shown on figure Q. The leg of the
angle gauge must be flush with the saw blade
(6) along its entire length;
5. Loosen the lock nut for 0° bevel angle (50);
WWW.VONROC.COM
6. Adjust the stop bolt for 0° bevel angle (32) until
the leg of the angle gauge is flush with the saw
blade along its entire length;
7. Re-tighten the lock nut for 0° bevel angle (50).
Subsequently check the position of the angle indi-
cator (19). If necessary loosen the pointer using a
Philips screwdriver, set to position 0° on the scale
for bevel angle (20) and re-tighten the retaining
screw.
Fine-tuning the 45° bevel angle (Fig. P, R)
1. Adjust the mitre and bevel angle to 45°;
2. Lower the handle (2) and secure it using the
position lock knob (38);
3. Lock the slide movement using the locking bolt
for slide rails (29);
4. Set an angle gauge to 45° and place it on the
table (11), as shown on figure R. The leg of the
angle gauge must be flush with the saw blade
(6) along its entire length;
5. Adjust the stop bolt for 45° bevel angle (31)
until the leg of the angle gauge is flush with the
saw blade along its entire length;
Subsequently check the position of the angle indicator
(19). If necessary loosen the pointer using a Philips
screwdriver, set to position 45° on the scale for bevel
angle (20) and re-tighten the retaining screw.
Fine-tuning the 0° mitre angle (Fig. B, G, S)
1. Set an angle gauge to 0° on the table (11) and
position it between the fence (9) and the saw
blade (6);
2. The leg of the angle gauge must be flush with
the saw blade (6) along its entire length;
3. Loosen all four fence bolts (51) and adjust the
fence (9) until the leg of the angle gauge is
flush with the saw blade along its entire length;
4. Retighten all four fence bolts (51) again.
Subsequently check the position of the angle
indicator (17). If necessary loosen the pointer
using a Philips screwdriver, set to position 0° on
the scale for mitre angle (16) and re-tighten the
retaining screw.
5. MAINTENANCE
Always make sure that the machine is not
connected to the mains electricity when you
carry out any maintenance of the mechanism.
EN
15