Special Safety Instructions - EINHELL PROFI Silver Line PS-WS 960-125 Mode D'emploi

Anleitung PS-WS 960-125_SPK1
tric tool's cable regularly and have it replaced by
an authorized specialist if it is damaged. Check
your extension cables regularly and replace them
if they are damaged. Keep handles dry, clean
and free from oil and grease.
Always pull out the power plug
- Whenever the electric tool is not being used
and before you start any maintenance work or
change the tools, for example when you change
the grinding discs.
Always remove keys and wrenches after use
- Always check that the flange wrench and other
adjusting tools have been removed before you
switch on the device.
Avoid unintentional starting
- Never carry the electric tool with your finger on
the switch button while the tool is connected to
the power supply. Make sure that the switch is
OFF when inserting the plug into the socket.
When using an extension cable outdoors
- Check that it is approved for outdoor duty and is
marked accordingly.
Be alert at all times
- Watch what you are doing. Use common sense
when working. Never use the electric tool when
you are distracted.
Check the electric tool for damage
- Before reusing the electric tool, carefully check
that the safety devices or any slightly damaged
parts are working as intended. Check that the
moving parts are in good working order, that they
do not jam, and that no parts are damaged. All
parts must be correctly assembled and meet all
the conditions required to ensure that the electric
tool works correctly. Unless otherwise stated in
the operating instructions, damaged safety devi-
ces and parts have to be repaired or replaced by
an authorized service center. Damaged switches
have to be replaced by a Customer Service
workshop. Never use electric tools with defective
ON/OFF switches.
Important!
- Use only the accessories or additional equip-
ment listed in the operating instructions. The use
of other tools and accessories may put you at
risk of injury.
Have repairs carried out only by a qualified
electrician
- This electric tool complies with the pertinent
safety regulations. Repairs may only be carried
out by a qualified electrician using genuine spare
parts, otherwise there is a risk of accidents.
Important!
- Your ability to react may be impaired by the
18.08.2005 16:32 Uhr Seite 11
consumption of alcohol, the taking of medication
and drugs, and by illness, fever or fatigue. Never
use electric tools unless you are 100% fit to do
so.

3. SPECIAL SAFETY INSTRUCTIONS

Any damaged power cables on the electric tool
must be replaced either by the manufacturer or a
service company authorized by the manufacturer.
Check that the speed shown on the disk is the
same or higher than the rated speed for this
angle grinder.
Check that the disk is of the correct size for this
angle grinder.
Grinding disks must be handled and stored with
care in accordance with the manufacturer's
instructions.
Examine the disk before using it. Never use disks
which have parts broken off or are cracked or in
any other way damaged.
Check that the grinding tools have been fitted in
accordance with the manufacturer's instructions.
Make sure that intermediate layers are used if
they are supplied with and required for the grin-
ding disk.
Make sure that the grinding disk is correctly fitted
and secured before you start to use the tool.
Allow the tool to run without load and in a safe
position for 30 seconds; stop the device imme-
diately if it vibrates heavily or if any other faults
become apparent. If this should be the case,
examine the machine to find the cause.
Never use separate reducer sleeves or adapters
to make grinding disks with larger holes fit the
tool.
For grinding disks with a thread insert, check that
the thread is long enough to hold the length of
the spindle.
Do not use cutting disks for roughing work.
Take precautions to ensure that flying sparks
cannot cause any danger (for example that they
do not hit anyone or cause inflammable sub-
stances to ignite).
If dust is generated during working, ensure that
the air vents are kept clear. If you should have to
remove dust, disconnect the electric tool from the
mains power supply first (use non-metallic objec-
ts only) and take care not to damage any parts
inside the tool.
The disk will continue to turn for a while after the
tool has been switched off.
Check that the mains power supply voltage is the
same as that specified on the rating plate.
GB
11