G Eneral Notes On Safety; U Se Of The Machine For Purposes For Which It Is Intended; I Ncorrect Use; Ec Declaration Of Conformity - SUHNER UMC 6-RL Dossier Technique

1. N
1.1 g
enerAl notes on sAfety
This operation manual is applicable for the machine UMC
6-RL. The machine may only be handled by personnel
who are qualified.
Hold power tools by insulated gripping surfaces when
performing an operation where the cutting tool may con-
tact hidden wiring or its own cord. Contact with a «live»
wire will make exposed metal parts of the tool «live» and
shock the operator.
WARNING Read all safety warnings and all in-
structions. Failure to follow the warnings and in-
structions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
1.2 u
se of the mAchine for purposes for
which it is intended
The machine is designed for filing, polishing,
and lapping work with files, polishing wheels,
and other attachments within the given spe-
cifications. It can work any material that does
not pose a hazard to health or the power tool.
1.3 i
ncorrect use
All uses other than those described under section
1.2 are regarded as incorrect use and are there-
fore not admissible.
1.4 ec
declArAtion of conformity
Otto Suhner GmbH of Trottäcker 50, D-79713 Bad Säck-
ingen, hereby declares under sole responsibility that the
product with the serial or batch no. (see reverse side) com-
plies with the requirements under the Directive 2014/30/
EU, 2006/42/EC, 2011/65/EU. Applied standards: EN ISO
12100, EN 60745, EN 55014-1, EN 55014-2, EN 61000-
3-2, EN 61000-3-3. Document Agent: T. Fischer. D-Bad
Säckingen, 10/2020.
T. Fischer/Division manager
2. C
2.1 p
rior to tAKing the mAchine into serVice
Before connecting tool to a power
source, be sure the voltage sup-
plied is the same as specified on
the name plate of the tool. The power sup-
ply should not vary more than 10% above or below the
voltage indicated on the nameplate. Check the tool before
use. Under no circumstances must the tool exceed the
22
S
oTES oN aFETy
ommISSIoNINg
max permitted speed. Observe national regulations.
2.2 t

AKing the mAchine into serVice

Preselect speed with adjusting wheel according to speed
table.
Level 1: 2500min
-1
Level 2: 3050min
-1
Level 3: 3600min
-1
Never start the machine without a tool!
2.2.1 t /t
unr on
The switch must be at the OFF position, i.e. the «0» is
visible. To switch ON the tool, press the switch, and push
it forwards until it engages audibly, i.e. the «1» becomes
bisible. Press the ON/OFF swith to trigger the blocking
and the machine shuts down.
2.3 r

Ating dAtA

Power voltage
Power Input 120/230V
Power Output 120/230V
Power Input 240V
Power Output 240V
Belt speed in idle
Sound pressure level EN 60745
Noise emission level
Vibration EN 60745
Weight w/o cord set
Protection class
The specified vibration value was measured with a
standardised test procedure. It can be used to
compare products or to make an initial assess-
ment of the exposure. The vibration emissions may differ
Level 4: 4150min
Level 5: 4700min
Level 6: 5250min
urn off
120/230/240V, 50/60Hz
600W
340W
580W
330W
5250min-1
85dB, K=3dB
96dB, K=3dB
7.5m/s , K=2.0m/s
2
1.9kg
-1
-1
-1
2
II